All Products

SKU: AF-3403 · MPN: 3403

The Feather M0 Express is Adafruit's CircuitPython-optimised Feather, built around the ATSAMD21G18 ARM Cortex M0+ processor. It combines the standard Feather M0 platform with 2 MB of SPI flash storage, a Mini NeoPixel, and a UF2 bootloader for drag-and-drop programming — no special tools or drive...

SKU: AF-3417 · MPN: 3417

The FeatherWing Tripler lets you connect a Feather board to two FeatherWings side by side — no stacking headers needed. All three sets of pins are cross-connected, with dedicated GND and 3.3 V strips for easy power distribution. Additional proto holes are available for custom wiring. Comes as a ...

SKU: AF-2890 · MPN: 2890

This is the FeatherWing Doubler - a prototyping add-on and more for all Feather boards. This is similar to our FeatherWing Proto except there are two! The magic of the Doubler comes when stacking a Feather and another board on top of the Doubler so you can work with both boards si...

SKU: AF-2203 · MPN: 2203

An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 16 pin 0.3" wide version. Best used with chips that have 16 pins (2x8) and have 0.3" pin spacing. These are often used for soldering into a Perma Proto ...

SKU: AF-2204 · MPN: 2204

An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 20 pin 0.3" wide version. Best used with chips that have 20 pins (2x10) and have 0.3" pin spacing. These are often used for soldering into a Perma Proto...

SKU: AF-5906 · MPN: ADA5906

The Adafruit Proto Doubler PiCowbell gives your Raspberry Pi Pico or Pico W two side-by-side socket slots — plug in your Pico on one side and a PiCowbell accessory on the other, no soldering or stacking headers required. It also adds LiPo battery charging, a power switch, reset button, STEMMA QT ...

SKU: AF-5200

The Adafruit PiCowbell Proto is a prototyping add-on board for the Raspberry Pi Pico and Pico W. It matches the Pico's footprint and sockets underneath, giving you a reset button, a STEMMA QT / Qwiic I2C connector, and a grid of prototyping pads — everything you need to quickly wire up custom cir...

SKU: DF-FIT0193

This is a very basic double sided prototyping board with standard 0.1" spacing with a 4x3mm (0.16x0.12") holes for mounting.The leaf pads makes you great for quickly prototyping stackable circuits.You can not only solder DIP components but also solder SMD components. You can solder the digit...

SKU: AF-3249 · MPN: 3249

Drive massive NeoPixel installations without blocking your code. The NeoPXL8 FeatherWing enables 8 concurrent DMA NeoPixel strands from a single Feather M0, with up to 250 pixels per strand (2,000 total) — all running in the background via hardware DMA so your code keeps executing. The wing hand...

SKU: AF-2796 · MPN: 2796

The Feather M0 Adalogger is an all-in-one datalogger built around the ATSAMD21G18 ARM Cortex M0 processor, with a built-in MicroSD card holder, native USB, and LiPo battery charging. With 256KB of flash and 32KB of RAM — 8× and 16× more than the ATmega328 or 32u4 respectively — it provides signif...

SKU: DF-DFR0406

INTRODUCTION The Arduino Motor Shield is based on L298 (a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors). It helps you drive two DC motors with Arduino board as well as control the speed and direction of the ...

SKU: PI-TSX00002

Need more room for your MKR Proto Shield? The MKR Proto Large Shield fits onto your MKR board using its provided female/male headers and enables you to fix it wherever you want with the mounting holes. This shield features a larger prototyping area with more than 300 solder points and m...

SKU: DF-DFR0131

Combines the power of screw shield and prototyping shield. This Proto Screw shield offers a better way to do prototyping. The Screw terminal can be screwed directly to the terminal on the thread and is reliable and convenient. It can be plugged into the Arduino controller. You can use thi...

SKU: PI-TSX00003

The MKR Relay Protoshield allows you to easily add relays to your MKR board based project. The shield provides two relays called RELAY1 and RELAY2 commanded by pin 1 and pin 2 respectively. The shield also provides easy connection by means of screw terminal...

SKU: PI-TSX00004

Add a SD slot and prototyping area in a single shield The Arduino MKR SD Proto Shield allows you to easily connect an SD card to your MKR form factor board. Use it to enhance the IoT features of your MKR1000, as well as store data coming from the web or sensors read by your board! There's al...

SKU: AF-3203 · MPN: 3203

The Adafruit Perma-Proto Bonnet Mini Kit is a prototyping daughter board sized for the Raspberry Pi Zero. It plugs directly onto the Pi's 2×20 GPIO header and provides a grid of 0.1″ soldering holes connected in a familiar breadboard pattern — making it easy to transfer circuits from a solderless...

SKU: AF-3825 · MPN: 3825

Testing is an important step in board manufacturing. And it can be super tricky on a fully populated PCB. So how can you test connections when you have an assortment of components blocking your probe? These "mini loop type" Small PCB Test Points easily snap in to your proje...

SKU: AF-2995 · MPN: 2995

The Feather M0 Bluefruit LE combines an ATSAMD21G18 ARM Cortex M0 processor with a Bluetooth Low Energy module, native USB, and LiPo battery charging. With the power of a 48 MHz ARM core and 256KB of flash, it provides significantly more processing headroom than the 32u4-based Bluefruit while mai...

SKU: AF-2772 · MPN: 2772

The Feather M0 Basic Proto is the no-frills member of the Feather M0 family, built around the ATSAMD21G18 ARM Cortex M0 processor with a built-in prototyping area for soldering on extra components. With 256KB of flash and 32KB of RAM, it provides significantly more processing power than ATmega-ba...

SKU: AF-2771 · MPN: 2771

The Feather 32u4 Basic Proto is the no-frills member of the Feather 32u4 family, with a built-in prototyping area where you can solder on extra components like buttons, sensors, or connectors without needing a separate breadboard. Built around the ATmega32u4 running at 8 MHz with 3.3V logic and ...