All Products

SKU: AF-269

The MAX31855 Thermocouple Amplifier Breakout converts K-type thermocouple readings into digital data via SPI, handling cold-junction compensation automatically. It measures temperatures from −200°C to +1350°C in 0.25°C increments, making it suitable for a wide range of temperature monitoring appl...

SKU: SF-SEN-13266

The SparkFun MAX31855K Thermocouple Breakout is a simple 14-bit resolution, SPI-compatible, serial interface thermocouple digitizer that makes reading a wide range of temperatures possible. A thermocouple works by taking two wires made of dissimilar metals, connecting them at the two ends, and...

SKU: DF-DFR0558

This Gravity I2C high-temperature sensor pairs a signal amplification module (MAX31855K) with a stainless steel sheathed K-type thermocouple probe for measuring temperatures up to 800 °C. The module converts the thermocouple's millivolt signal to a 14-bit digital reading over I²C, with cold-junct...

SKU: DF-SEN0656 · MPN: SEN0656

The CT1780 is a cold-junction compensated amplifier for K-Type thermocouples, designed to make extreme temperature measurement easier to add to microcontroller projects. It digitises the tiny thermocouple signal and provides temperature readings with 0.25℃ resolution over a very wide measurement ...

SKU: AF-1552

This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 2.1W channels into 4 ohm impedance speakers (@ 10% THD). Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, it's incredibly efficient (89% efficient when...

SKU: AF-987

This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 3.7W channels into 3 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, its incredibly efficient (over 90% efficient when driving...

SKU: AF-5870 · MPN: ADA5870

This compact breakout adds a high-resolution, single-channel ADC to your I2C bus, making it a handy choice for precision differential measurements. It is built around the MCP3421, a simple and low-cost 18-bit ΔΣ converter with adjustable gain, a built-in precision reference voltage, and support f...

SKU: AF-270

A Type-K thermocouple with fiberglass braid insulation, rated to 500°C — far beyond the ~200°C limit of standard vinyl-insulated thermocouples. The bare bead probe design is suited to measuring both air and surface temperatures in high-heat environments such as ovens, kilns, heaters, and industri...

SKU: AF-1778

The AD8495 from Analog Devices is an analog-output K-type thermocouple amplifier on a compact breakout board. Simply power the board with 3–18V DC, connect a K-type thermocouple to the terminal block, and read the temperature as a voltage on the OUT pin — no digital protocols or complex configura...

SKU: AF-1712

A mini class D with AGC and I2C control? Yes please! This incredibly small stereo amplifier is surprisingly powerful. It is able to deliver 2 x 2.8W channels into 4 ohm impedance speakers (@ 10% THD) and it has a i2c control interface as well as an AGC (automatic gain control) system to keep your...

SKU: AF-3263

The Adafruit Universal Thermocouple Amplifier MAX31856 Breakout reads temperature from virtually any thermocouple type — K, J, N, R, S, T, E, or B — with 0.0078125°C resolution and a measurement range of -210°C to +1800°C. It handles cold-junction compensation, linearisation, and fault detection ...

SKU: AF-3245

Thermocouples are best used for measuring temperatures that can go above 100°C. This is a bare wires stainless-steel tip probe which can measure air or surface temperatures. Most inexpensive thermocouples have a vinyl covering which can melt at around 200°C, this one uses a fiberglass braid so...

SKU: SF-BOB-13878

The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire Wheatstone bridge configuration. If you open up an electronic bathroom scale, you’ll find a large rat’s nest of wires. The Load Sensor Combinator was created to combine the 12 wires foun...

SKU: SF-SEN-16295

The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junction) and one for the chip itself (the cold junction). As a result, the MCP9600 ...

SKU: AF-3328

The Adafruit PT100 RTD Temperature Sensor Amplifier is a breakout board for the MAX31865 precision RTD-to-digital converter. It reads 2-, 3-, or 4-wire PT100 platinum resistance temperature detectors over SPI, delivering laboratory-grade temperature accuracy and repeatability that surpasses therm...

SKU: DF-DFR0123

This 20W adjustable DC-DC boost converter with a digital display is based on the professional boost chip and supports 3~32V power input, 5~35V output, and an accuracy of ±0.05V. The switching frequency is 400KHz, the conversion efficiency can reach 94%, it has the functions of overheating prote...

SKU: SF-SEN-16294

The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junction) and one for the chip itself (the cold junction). As a result, the MCP9600 ...

SKU: SF-DEV-22462

The SparkFun DataLogger IoT is a data logger that comes preprogrammed to automatically log GPS and various pressure, humidity, and distance sensors. All without writing a single line of code! The DataLogger automatically detects, configures, and logs Qwiic sensors. It was specifically designed fo...

SKU: AF-1727

The MAX31850K breakout board is a 1-Wire thermocouple amplifier with cold-junction compensation for K-type thermocouples. Unlike SPI-based amplifiers, the 1-Wire interface allows any number of thermocouple breakouts to share a single data line — ideal for multi-point temperature measurement. The...

SKU: AF-1492

Break out those tricky 0.5 mm pitch flex cable connections to breadboard-friendly 0.1" spaced headers with this FPC adapter board. The 50-pin connector on top accommodates most ZIF and snap-style FPC connectors, and each pin is broken out to a standard 0.1" × 0.1" header pad for easy prototyping....