All Products
Showing 1-20 of 49 products · 11 unavailable products hidden
Adafruit CAN Pal - CAN Bus Transciever
·
The Adafruit CAN Pal is a CAN bus transceiver breakout for microcontrollers that have a native CAN peripheral. It converts 3.3V logic-level CAN TX/RX signals to the differential signalling required for the CAN bus. This is a transceiver only — it does not include a CAN controller, so your microco...
Alchitry Hd V2 Dual Micro HDMI Expansion Board
·
Add HDMI connectivity to your Alchitry Au or Pt FPGA setup with this expansion board. It provides two micro HDMI ports for video-related projects and FPGA experiments.Each HDMI port can be configured as either a source or a sink using solder jumpers, giving you flexibility when building display, ...
50-pin FPC Extension Board + 200mm Cable
·
This 50-pin FPC extension board lets you add approximately 22cm of reach to any 50-pin, 0.5mm pitch FPC/FFC connection. The board features two 50-pin flex connectors with a 200mm (20cm) FPC cable included, giving a total extension of about 22cm when the board length is included. Works with 50-pi...
40-pin FPC Extension Board + 200mm Cable
·
A 40-pin FPC extension board with an included 200mm flexible flat cable. Adds approximately 22cm of reach (20cm cable plus 2cm board) to devices using 40-pin, 0.5mm pitch FPC/FFC connections such as TFT displays. The board features two 40-pin flex connectors (both bottom-contact type), allowing ...
DFRobot Building Block Expansion Board Bundle for UNIHIKER M10
·
This bundle adds motor, servo and sensor expansion to the UNIHIKER M10 single-board computer, using the included Type-C to HY2.0-4P communication cable to bridge the M10 to the expansion board.The board includes an integrated 18650 battery holder so your controller, motors and sensors can run fro...
DFRobot Fermion BMI323 6DOF IMU Sensor
·
Built around the Bosch BMI323, this compact Fermion module combines a 3-axis accelerometer and a 3-axis gyroscope on a 16 mm × 16 mm board. It provides high-rate acceleration and angular velocity data over I²C for embedded motion sensing, wearables, robotics, battery-powered IoT nodes and compact...
LattePanda IOTA 51W PoE Expansion Board (IEEE 802.3bt)
·
Designed specifically for the LattePanda IOTA single-board computer, this expansion board adds IEEE 802.3bt PoE++ power and Gigabit Ethernet data over a single Ethernet cable. It can deliver up to 51W, helping simplify installations where a separate power adaptor would be awkward or where periphe...
ShakeUp Standard Kit
The ShakeUp makes you a STEAM inventor by helping you to connect everyday objects to your computer. If you can plug in a Keyboard and Mouse, you can use the ShakeUp. The Magic Science When you plug the ShakeUp into your computer, your computer thinks it's just a regular keyboard and mous...
Alchitry Sp V2 FPGA Spacer Board
·
This spacer board gives your FPGA stack a little extra breathing room. It adds 5.6mm of space between stacked boards, helping make room for the included heatsink.It is also handy when you need clearance for cables between the Ft and port 1 on the Hd, keeping your stacked Alchitry setup easier to ...
Raspberry Pi Motor Driving Expansion Board (Compatible with Raspberry Pi 4B / 3B+ / 3B / Zero)
·
##Introduction The multifunctional motor driver expansion board is designed for Raspberry Pi Zero/Zero W/A+/B+/2B/3B/3B+/4B. This fully-featured robot motor expansion board is capable of supporting multiple motors, stepper motors, and servos simultaneously. It also provides spare camera and DIP d...
RTK Facet Main Board v13 Replacement PCB
·
This is the main PCB assembly used in the RTK Facet, supplied as a replacement part for repairing an existing device.It is intended for users who are comfortable disassembling and servicing their RTK Facet. The open source hardware design helps make it possible to understand the unit and carry ou...
Thing Plus RP2350 Wireless Development Board (Ding & Dent)
·
This Thing Plus board is a wireless development platform built around the Raspberry Pi Foundation RP2350 microcontroller. It combines the familiar Thing Plus form factor with Qwiic expansion, a µSD card socket, USB-C, LiPo charging hardware and a fuel gauge for local or remote projects.The RP2350...
AltIMU-10 v5 Gyro, Accelerometer, Compass, and Altimeter (LSM6DS33, LIS3MDL, and LPS25H Carrier)
The Pololu AltIMU-10 v5 is a compact inertial measurement unit (IMU) and altimeter that combines a gyroscope, accelerometer, magnetometer, and barometric pressure sensor on a single board. It provides ten independent measurements — pressure, 3-axis rotation, 3-axis acceleration, and 3-axis magnet...
Adafruit 9-DOF LSM9DS1 Breakout Board - STEMMA QT / Qwiic
·
Add motion, direction and orientation sensing to your project with this compact STEMMA QT version of the LSM9DS1 9-DOF sensor from Adafruit. The LSM9DS1 combines a 3-axis accelerometer, 3-axis magnetometer and 3-axis gyroscope into a single chip for full orientation tracking. This version featur...
Alchitry Io V2 Element Board
·
The Io V2 is an Alchitry Element Board designed for learning and experimenting with digital design on Alchitry Au and Cu FPGA development boards. It keeps the same beginner-friendly controls and indicators as the original Io, now in the Alchitry V2 form factor.On-board interactive hardware includ...
Adafruit Feather RP2040
·
The Feather RP2040 brings the Raspberry Pi RP2040 dual-core processor to the Feather platform. With two ARM Cortex M0+ cores running at ~125 MHz, 264 KB SRAM, 8 MB SPI flash, and the RP2040's unique PIO (Programmable I/O) state machines, this board offers excellent performance for CircuitPython, ...
RDK X5 PoE Expansion Board with Fan & Heatsink, 802.3af/at
·
Transform your D-Robotics RDK X5 development board into a powerhouse of connectivity and reliability with the latest Power Over Ethernet Expansion Board. Designed to seamlessly integrate with the RDK X5, this PoE module not only simplifies your network setup by combining data and power into a sin...
Kitronik :VIEW Graphics 128 OLED display 128x64 for BBC micro:bit
The Kitronik :VIEW Graphics128 OLED display gives the user the ability to add a monochrome 128x64 display to the BBC micro: bit. The onboard edge connector allows the micro:bit to slot into the board without any additional fixings. The board also features a micro:bit style I/O connector which mea...
Micro: bit GPIO Expansion Board
This is a GPIO expansion board for Micro: bit, it’s convenient to operate. It can be inserted the expansion board directly into the Micro: bit, and this expansion board can be cascaded.SpecificationsSize: 64 x 37 x 12 mmPackage listMicro: bit GPIO expansion board x 1
USB Patterned Fabric Cable - A/MicroB 1m
Oooh it's so soft and pretty! If you have to have visible cables then you might as well have the nicest fabric bound cable with a eye-catching snake-like pattern. That's why we now carry this standard A to micro-B USB cable for USB 1.1 or 2.0. Perfect for connecting a PC to your BBC Micro:...
