All Products

SKU: AF-4718 · MPN: 4718

The Adafruit SPI Non-Volatile FRAM Breakout provides 2 Mbit (256 KBytes) of ferroelectric RAM (FRAM) storage over SPI. FRAM combines the non-volatile retention of flash with the instant read/write speed of SRAM — no page writes, no block erasing, and each byte can be written 10 trillion times wit...

SKU: AF-4719 · MPN: 4719

The Adafruit SPI Non-Volatile FRAM Breakout provides 4 Mbit (512 KBytes) of ferroelectric RAM (FRAM) storage over SPI. FRAM combines the non-volatile retention of flash with the instant read/write speed of SRAM — no page writes, no block erasing, and each byte can be written 10 trillion times wit...

SKU: AF-1897 · MPN: 1897

The Adafruit SPI Non-Volatile FRAM Breakout provides 64 Kbit (8 KBytes) of ferroelectric RAM (FRAM) storage over SPI. FRAM combines the non-volatile retention of flash with the instant read/write speed of SRAM — no page writes, no block erasing, and each byte can be written 10 trillion times with...

SKU: AF-3533 · MPN: 3533

The Adafruit 0.96" 160×80 Colour TFT Display Breakout is a tiny, high-density full-colour screen driven by the ST7735R controller. Despite its thumbnail size, it packs 160×80 RGB pixels and communicates over 4-wire SPI, making it compatible with virtually any microcontroller — even those with lim...

SKU: AF-1870 · MPN: 1870

A simple sewable breakout board with a CR2032 coin cell battery holder pre-soldered on and 0.1" pitch breakout pins for easy connection. Ideal for powering very low-current projects or adding a battery backup circuit to a real-time clock or similar module. Key Features CR2032 Coin Cell Holder ...

SKU: DF-SEN0407

The LIS331HH is an ultra-low-power high precision triple-axis linear accelerometer with 16-bit data output. It has user selectable full scales of ±6g/±12g/±24g and is capable of measuring accelerations with output data from 0.5Hz to 1kHz. Its power consumption is as low as 10μA. The device contai...

SKU: SF-DEV-27877 · MPN: DEV-27877

The Br V2 is a breakout board for Alchitry headers, giving you access to all the signal pins through solder-friendly 0.1" holes. It is designed to make wiring, prototyping and adding your own circuitry easier when working with an Alchitry board.This is the wide version, recommended for most uses ...

SKU: SF-BOB-08891

This breakout board provides a convenient PCB adapter for MQ-series gas sensors (MQ-3, MQ-4, MQ-6, MQ-7, and MQ-8). It converts the sensor's oversized, oddly-spaced pins into a standard breakout format that's easy to wire up to a microcontroller. Connect 5 V, ground, and a load resistor to an AD...

SKU: AF-6014 · MPN: ADA6014

This compact breakout board is designed for the Raspberry Pi 5 and Adafruit RP2350 boards that use an HSTX connector. These boards use a 22-pin FPC connection to carry high-speed video data over differential pairs, and this breakout gives you a handy way to adapt that interface for a custom setup...

SKU: SF-BOB-12941

With SD and MMC memory prices dropping, the time is right for mass storage and datalogging. This breakout board will allow you to breakout the SD/MMC socket to a standard .1" 10-pin header. Perfect for breadboarding and the likes. Board comes fully assembled and tested as shown. Dimensions: 1.3"...

SKU: SF-LCD-13722 · MPN: LCD-13722

Add a tiny, crisp OLED to your next microcontroller project without taking up much space. This breakout carries a monochrome Blue-on-Black display that is only 64 pixels wide by 48 pixels tall, yet still has room for useful graphics, status screens and simple game interfaces.It is easy to drive f...

SKU: AF-1764 · MPN: 1764

Simple but effective - this breakout board has a USB Mini-B connector, with all 5 pins broken out. Great for pairing with a microcontroller with USB support, or adding USB 5V power to a project.Comes with one fully assembled and tested mini B breakout PCB and a small stick of 0.1" header so yo...

SKU: SF-BOB-11722

This is a clever little breakout board for both the RGB and R/G illuminated rotary encoders. On one side, it breaks out all of the RGB pins to standard, breadboard friendly, 0.1" headers. Turn it over and it has a footprint for the R/G version! Simply solder an encoder down to the board and you’r...

SKU: SF-PRT-10588

Simple breakout board for the 3.5mm audio jack. Use this breakout (shipped bare) to allow breadboard or SIP access to the super-common 3.5mm audio jack. All five pins are broken out.

SKU: AF-2743 · MPN: 2743

This compact adapter board makes it easier to work with ARM development boards that use the slimmer 2x5 SWD programming connector. It is designed for 0.05 inch / 1.27mm pitch SWD cables, commonly found on small Cortex M0 and Cortex M3 boards.It is useful when connecting JTAG/SWD debugging tools s...

SKU: SF-BOB-17110 · MPN: BOB-17110

USB-C is handy for modern projects, but its 24 tiny, tightly spaced pins are not friendly to hand soldering or quick prototyping. This breakout board routes the essential USB-C connections out to a standard 0.1" (2.54mm) pitch so you can work with them on breadboards, perfboards and other prototy...

SKU: AF-4634 · MPN: 4634

Add motion, direction and orientation sensing to your project with this compact STEMMA QT version of the LSM9DS1 9-DOF sensor from Adafruit. The LSM9DS1 combines a 3-axis accelerometer, 3-axis magnetometer and 3-axis gyroscope into a single chip for full orientation tracking. This version featur...

SKU: DF-DFR0239

This small size breakout is programmable full-color RGB LED for hobbyists, industrial designers, prototypers, and experimenters. It is designed to allow the easy addition of dynamic indicators, displays, and lighting to existing or new projects. Controlled by PWM channels can be available in s...

SKU: AF-5221 · MPN: 5221

This breakout PCB converts the ANO rotary navigation encoder's non-standard pinout into a straightforward, breadboard-friendly header strip. The ANO encoder combines a rotary encoder with directional and centre-push buttons — similar to classic scroll wheel interfaces — and this PCB makes it easy...

SKU: SF-BOB-16998 · MPN: BOB-16998

Add a reversible USB-C connector to your project without hand-soldering the tiny SMD pads. This horizontal breakout makes it easier to bring USB-C power and data connections onto a prototype or custom build.The board breaks out the USB-C connector’s VBUS, GND, CC1, CC2, D+ and D- pins to 0.1" pit...