All Products

SKU: AF-5580

The Adafruit MAX17048 LiPoly/LiIon Fuel Gauge and Battery Monitor gives you accurate battery voltage and charge percentage readings for your 1S 3.7–4.2V lithium polymer or lithium ion battery. Instead of guessing remaining capacity from a non-linear voltage curve, this smart sensor does the maths...

SKU: SF-PRT-12711

The SparkFun USB LiPoly Charger is a single-cell Li-Ion/Li-Polymer battery charging board based on the MCP73831T. It charges 3.7V LiPo cells at a selectable rate of 500 mA or 100 mA via a solder jumper, with power input from either USB or a barrel jack connector. The board includes a SYS OUT JST...

SKU: AF-5383

This small, palm-sized battery power meter has a small display that shows off how much juice is left in your single Lithium Ion/Polymer rechargeable battery. The color display has four levels of power indication once battery capacity becomes 100%, 75%, 50%, and 25%. When power is below 25%, only ...

SKU: AF-4712

The Adafruit LC709203F Fuel Gauge monitors your single-cell LiPo or Li-Ion battery and reports both voltage and state of charge as a percentage over I2C. It handles the non-linear voltage-to-percentage conversion for you, so your project always knows exactly how much battery is left — just like t...

SKU: LB-00253

A compact 3.7 V lithium-ion polymer (LiPo) battery with a 180 mAh capacity (~0.6 Wh). Thin, lightweight, and fitted with a genuine 2-pin JST-PH connector for reliable, snag-free connections to compatible chargers and development boards. Includes built-in protection circuitry to guard against ove...

SKU: AF-4410

The Adafruit Micro-Lipo Charger is a tiny, easy-to-use charger for single-cell 3.7V/4.2V lithium polymer and lithium ion rechargeable batteries. Simply plug a USB-C cable into any USB power source and connect your battery via the JST connector — two LEDs show charging status at a glance (red = ch...

SKU: AF-5397

The Adafruit LiIon/LiPoly Charger BFF is a compact battery charging add-on designed to mount directly onto the back of any QT Py board. It makes portable power simple — plug in a standard 3.7 V/4.2 V lithium battery, and the charger handles the rest via the QT Py's USB-C connection. When USB is ...

SKU: AF-6495 · MPN: ADA6495

This BFF add-on makes it much easier to wire up small QT Py and Xiao projects without juggling loose jumpers. Plug in a compatible board and each pin is brought out to a screw-terminal block, with an extra socket pin available for quick wire connections.It also adds a Stemma QT / Qwiic connector ...

SKU: AF-6359 · MPN: ADA6359

This breakout lets you add an ideal diode to a higher-current DC power path without the usual forward voltage drop of a standard diode. It is designed for 3~23V DC supplies and up to 5A, using the LM73100's back-to-back FETs to keep current flowing in one direction while wasting far less power as...

SKU: AF-6391 · MPN: ADA6391

This small accessibility tool helps remove LiPoly and LiIon batteries with JST connectors from a board without tugging on the battery wires.The 3D-printed puller slips over the JST PH connector so you can line it up with the socket and gently lift it out. It is handy for anyone who finds tiny bat...

SKU: LB-00238

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 1200mAh for a total of about 4.5 Wh.The batteries come pre-attached with a genuine 2-pin JST-PH connector a...

SKU: AF-2011

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 2000mAh. If you need a larger (or smaller!) battery, we have a full range of LiPoly batteriesThe batteries ...

SKU: AF-3399

For many years, instructors and teachers have asked us to come up with a better way to teach programming and electronics. We have worked on Circuit Playground Express for over a year to come up with a board that is powerful, beautiful, fun, and perfect for teaching Code.org CS Discoveries Circ...

SKU: AF-3428

A voltage detector is handy for projects where you want to make sure your microcontroller doesn't run at a low voltage. For example, say you have a Feather Huzzah running on a lipoly battery every few minutes. Eventually the battery runs down, and goes below 3.3V, so the voltage to the ESP8266...

SKU: AF-259

This is a Lithium Ion and Lithium Polymer battery charger based on the MCP73833. It uses a USB mini-B for connection to any computer or 'USB wall adapter'. Charging is performed in three stages: first a preconditioning charge, then a constant-current fast charge and finally a constant-volta...

SKU: AF-258

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 1200mAh for a total of about 4.5 Wh. If you need a larger battery, we also have a 2500mAh+ modelThe batteri...

SKU: AF-328

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 2500mAh for a total of about 10 Wh. If you need a smaller battery, we also have a 1200mAh model The batter...

SKU: AF-261

Red and black tinned wires with a 2-pin JST PH connector on the end. 4" / 100mm long. Matches up nicely with our Lipoly chargers! We have the socket 'mating' version of this cable over here, as well as an 'extension' cable that has one of each soldered together. If you want a switch in t...

SKU: AF-3064

By popular request - we now have a way you can turn on-and-off Lithium Polymer batteries without unplugging them. This PH2 Female/Male JST 2-pin Extension Cable comes with an in-line Switch - click once to turn on, click again to turn off. It's super handy especially in tandem with o...

SKU: AF-3000

Would you like to learn electronics, with an all-in-one board that has sensors and LEDs built in? Circuit Playground is here - and it's the best way to practice programming on real hardware with no soldering or sewing required! This is the Classic version of Circuit Playground, which come...