All Products
Showing 1-20 of 44 products · 16 unavailable products hidden
JST-PH Battery Extension Cable - 500mm
·
A 500 mm extension cable with a JST-PH 2-pin socket on one end and a matching plug on the other. The colour-coded wires make it easy to verify correct polarity. Compatible with JST-PH terminated battery packs including LiPo, Li-Ion, and AAA battery holders. Key Features JST-PH 2-Pin Connectors...
3 x AAA Battery Holder with On/Off Switch, JST, and Belt Clip
·
A slim 3×AAA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making it an ideal non-rechargeable alternative for 3.3V projects that use a JST battery...
Switched JST-PH 2-Pin SMT Right Angle Breakout Board
·
This switched JST connector is the best way to quickly prototype with our LiPoly batteries. We paired a genuine JST connector with a slide switch that can do up to 600mA. Both are soldered onto a breadboard-friendly breakout. There's two ground pins, one 'switched' power pin, and one pin that ...
2 x AA Battery Holder with On/Off Switch JST PH Connector
·
A slim 2×AA battery holder with a built-in on/off switch and genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and portable builds without needing to disconnect the battery to turn off power. The...
LED Glasses Accessories Kit
·
An accessories kit for building a complete Adafruit LED Glasses project. Includes a chunky plastic glasses frame as a mechanical base, a STEMMA QT cable for connecting the LED panel to the driver board, a portable battery holder with belt clip, an extension cable, and mounting hardware. Key Feat...
JST-PH 2-pin Jumper Cable - 100mm long
·
We use 2 pin JST PH connectors for all our battery packs, and if you want to put a board in series, like our LC709203F Stemma QT battery gauge, this cable will be very handy! Both ends have a JST PH 2mm pitch 2-pin plug. Between the two, 100mm of color coded wire - red for power, black for gro...
In-line power cable 1 meter long extension cord (for EL wire)
·
Give yourself some more room with an EL wire cable extender. This cable has a 2-pin JST SM plug on one end and receptacle on the other. Use it to extend the reach of EL wire, panel, tape, etc. The cable is a meter long, you can of course snap more together if necessary, or cut and re-solder it...
JST 2-pin cable
·
Red and black tinned wires with a 2-pin JST PH connector on the end. 4" / 100mm long. Matches up nicely with our Lipoly chargers! We have the socket 'mating' version of this cable over here, as well as an 'extension' cable that has one of each soldered together. If you want a switch in t...
4Ω 6W Speaker
This compact enclosed speaker delivers clear audio output at up to 6W with a 4Ω impedance, suitable for a wide range of DIY audio and display projects. It comes with a JST PH 2-pin input cable for easy connection to amplifier boards and audio-capable development boards. Key Features Enclosed D...
Battery Holder 3xAA with Cover and Switch - JST Connector
This 3xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover as well as an ON/OFF switch that can be used to control power to your project. The 6" (~150mm) cable has been terminated with a JST connector. Note: Please keep in...
Mono Enclosed Speaker - 1W 8 Ohm
This compact enclosed mono speaker delivers clear audio at up to 1 W with 8 Ω impedance. The sealed enclosure provides better volume and sound quality compared to bare speaker drivers of a similar size, making it a practical choice for embedded audio projects, displays, and interactive installati...
6V Air Valve with 2-pin JST PH Connector - FA0520E
·
The 6V Air Valve (FA0520E) is a 3-port solenoid valve for pneumatic systems, functioning similarly to an electrical relay. It features a common port (COM), a normally open port, and a normally closed port, allowing you to switch air flow direction by powering the valve on or off. The valve is ra...
3-Wire JST to Molex Cable
·
This simple adapter cable makes it easy to connect between 3-pin JST and 3-pin Molex connectors in your electronics project.It has a 3-pin Molex connector on one end and a 3-pin JST connector on the other, both with 0.1" spacing. The three-wire cable is handy for adapting sensors, boards or small...
Micro:bit AA battery holder with Switch
A 2× AA battery holder with on/off switch, designed for powering the BBC micro:bit on the go. The JST connector plugs directly into the micro:bit's battery port, and the ~14 cm cable provides enough length for flexible mounting. Key Features 2× AA Battery Holder – Provides 3 V from standard AA...
2.5mm Pitch 2-pin Cable Matching Pair - JST XH compatible
·
A matching pair of 2-pin JST XH-compatible cables — one with an inline plug and one with an inline socket — for easy connect-and-disconnect wiring. The 2.5mm pitch connectors friction-lock together for a secure, reliable connection that's easy to separate when needed. Each cable is 20cm long wit...
JST Jumper 2 Wire Assembly
This is a simple two wire cable. Great for jumping from board to board or just about anything else. There is a 2-pin JST connector on one end, bare cable on the opposite end. It also comes with the mating connector for the JST. Dimensions: 6" length Documents: JST connector Datasheet Illumitu...
Circuit Playground Express Educator's Pack
·
The Circuit Playground Express Educator's Pack is a comprehensive classroom kit built around Adafruit's versatile Circuit Playground Express board. It includes everything educators need to teach electronics, coding, and wearable technology — from conductive thread and servos to battery packs and ...
JST PH 2-Pin Cable – Male Header 200mm
·
For a really long time we assumed that the JST PH didn't have a free-hanging male header version. But then we found this JST-PH 2-pin Male Cable, and we were like, this is perfect! It's not a genuine JST connector, but it's 100% compatible with a nice clicky connection that you can ...
2-pin JST SM Plug + Receptacle Cable Set
·
This matching cable set includes one 2-pin JST SM plug and one 2-pin JST SM receptacle, each with 16cm leads. The latching connectors provide a solid, compact connection that won't come apart easily, and the polarised design prevents backwards insertion. These cables are compatible with EL wire ...
FLORA Sensor Pack
·
Sense the world around you! The FLORA Sensor Pack includes many types of sensors for your wearable enjoyment. Sense motion, direction, color, light levels, touch, and connections with FLORA sensor breakouts and conductive materials, and a few NeoPixels for experimenting with displaying your se...
