All Products

SKU: AF-3417

The FeatherWing Tripler lets you connect a Feather board to two FeatherWings side by side — no stacking headers needed. All three sets of pins are cross-connected, with dedicated GND and 3.3 V strips for easy power distribution. Additional proto holes are available for custom wiring. Comes as a ...

SKU: AF-2926

The Terminal Block Breakout FeatherWing kit is like the Golden Eagle of prototyping FeatherWings (eg. majestic, powerful, good-looking). To start, you get a nice prototyping area underneath your Feather, with extra pads for ground, 3.3V and SDA/SCL. Not one to stop there, we expanded t...

SKU: AF-3173

A simple, solder-on terminal block set sized to fit Adafruit Feather boards and FeatherWings. These 0.1″ pitch terminal blocks let you make secure, screw-down wire connections without soldering wires directly to your board — making projects easier to build, maintain, and modify. Compatible with ...

SKU: SF-PRT-22461

A 10-way 3.5mm-pitch PCB terminal block paired with a matching rising clamp screw socket. Together they provide robust, solderless I/O and power connections for prototyping and production boards alike. The terminal block solders to your PCB at a 90° angle, while the rising clamp socket plugs in ...

SKU: AF-5709

The Adafruit CAN Bus FeatherWing adds CAN bus networking to any Feather board. It uses the MCP2515 CAN controller and TJA1051/3 transceiver to send and receive messages in standard or extended format at up to 1 Mbps over a two-wire differential bus. Only an SPI port and two pins (chip-select and ...

SKU: AF-2927

A Feather board without ambition is a Feather board without FeatherWings! This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 stepper and 2 DC motors). Using our Feather Stacking Headers or Feather Fem...

SKU: AF-4004

Woohoo, it's time for a Particle Mesh party! So why not cater for connectivity with the Particle Mesh Wi-Fi Bundle, a veritable smörgåsbord (yum!) to begin building mesh networking for your IoT project. Particle Mesh means you can create local networks that collect data, share messages, and co...

SKU: AF-2884

The FeatherWing Proto is a prototyping add-on board compatible with all Adafruit Feather boards. It provides duplicate breakouts for every Feather pin, a grid of proto holes for custom circuitry, and connected pad strips for GND and 3.3V — everything you need to add custom components to your Feat...

SKU: DF-DFR0924

A terminal block expansion board for the Raspberry Pi Pico, designed for makers who prefer screw-terminal connections over soldering or breadboard wiring. Every Pico pin is broken out to a labelled terminal block, providing stable and reliable connections for prototyping and permanent installatio...

SKU: AF-2136

A compact 3-pin screw terminal block with 2.54mm (0.1") pitch, designed to fit directly into perfboard and protoboards. Terminal blocks provide reliable, tool-adjustable PCB-to-wire connections that are easy to maintain and reconfigure. The screw terminals accept a range of wire gauges and are t...

SKU: AF-3798

A DIN rail-mountable adapter that breaks out all 8 wires of an RJ-45 (Ethernet) cable to screw terminal blocks. Connect an RJ-45 cable to the vertical jack, and access each wire individually via the terminal blocks — no soldering required. This adapter simplifies wiring in DIN rail builds by let...

SKU: AF-2928

The 8-Channel PWM or Servo FeatherWing adds 8 channels of 12-bit PWM output to any Adafruit Feather board via I2C. It uses an onboard PWM driver with a built-in clock, so it runs independently without tying up your microcontroller — unlike the TLC5940 family, no continuous signal is needed. The ...

SKU: AF-5967 · MPN: ADA5967

The Adafruit Proto Tripler PiCowbell gives your Raspberry Pi Pico or Pico W three side-by-side socket slots — plug in your Pico and up to two PiCowbell accessories with no soldering or stacking headers required. It also includes LiPo battery charging, a power switch, reset button, STEMMA QT conne...

SKU: AF-3628

This adapter converts a USB-A male plug into a 5-pin screw terminal block, making it easy to connect bare wires to a USB port without soldering. Just loosen the terminal screws, insert your stranded or solid-core wire, and tighten. All five pins are clearly labelled (VCC, D−, D+, GND, and Shield/...

SKU: AF-2895

The Adafruit Non-Latching Mini Relay FeatherWing lets you control mains-powered devices and small appliances using any Feather microcontroller. Switch lamps, fans, solenoids, and other loads rated up to 250 VAC or DC — all from a compact FeatherWing form factor. This is the non-latching version,...

SKU: AF-2138

A compact 2-pin screw terminal block with 2.54mm (0.1") pitch, designed to fit directly into perfboard and protoboards. Terminal blocks provide reliable, tool-adjustable PCB-to-wire connections that are easy to maintain and reconfigure. The screw terminals accept a range of wire gauges and are t...

SKU: AF-2139

A compact 5-pin screw terminal block with 2.54mm (0.1") pitch, designed to fit directly into perfboard and protoboards. Terminal blocks provide reliable, tool-adjustable PCB-to-wire connections that are easy to maintain and reconfigure. The screw terminals accept a range of wire gauges and are t...

SKU: AF-4437

This one's going out to all the makers and designers who use DIN railing in their builds. This adapter plate is perfect for simplifying complex wiring. You connect a 2x20 IDC cable to this very PCB, which can be DIN rail-mounted. Then, all 40 pins are broken out into terminal blocks, so...

SKU: AF-2134

A compact 9-pin screw terminal block with 2.54mm (0.1") pitch, designed to fit directly into perfboard and protoboards. Terminal blocks provide reliable, tool-adjustable PCB-to-wire connections that are easy to maintain and reconfigure. The screw terminals accept a range of wire gauges and are t...

SKU: AF-2142

A compact 10-pin screw terminal block with 2.54mm (0.1") pitch, designed to fit directly into perfboard and protoboards. Terminal blocks provide reliable, tool-adjustable PCB-to-wire connections that are easy to maintain and reconfigure. The screw terminals accept a range of wire gauges and are ...