All Products
Showing 1-20 of 47 products · 13 unavailable products hidden
Board Edge Mounting Kit - Pack of 4
Board edge mounting standoffs designed to grip standard 1.6 mm (0.062") thick PCBs by the edge or corner — no mounting holes required. An elegant solution for securing boards like the original Raspberry Pi or any PCB without pre-drilled mounting points. Key Features No Mounting Holes Needed – ...
Adafruit 4x4 Trellis Feather Acrylic Enclosure + Hardware Kit
This laser-cut acrylic enclosure kit turns your 4×4 NeoTrellis setup into a handheld device with an elegant black and white design and beautifully diffused button illumination. Designed to house any Adafruit Feather board (except FONA) alongside the NeoTrellis RGB Driver PCB. The enclosure inclu...
10 sets M3 * 30 hexagonal standoffs mounting kit
A 10-pack of M3 × 30mm hexagonal standoffs with matching screws and nuts. Use them to mount circuit boards, sensors, and other components with consistent 30mm spacing and secure mechanical support. The male/female design allows standoffs to be stacked for even greater clearance. At 30mm height, ...
Adafruit FunHouse Mounting Plate and Yellow Brick Stand
The Adafruit FunHouse Mounting Plate and Yellow Brick Stand is an accessory kit for the Adafruit FunHouse IoT development board. It includes a laser-cut acrylic mounting plate that attaches to the back of your FunHouse, plus a set of yellow building bricks for creating a tabletop stand. Wall moun...
10 sets M3 * 6 nylon screws
A 10-pack of M3 × 6mm nylon standoffs with matching screws and nuts. Nylon standoffs are non-conductive, making them ideal for isolating circuit boards from metal chassis or other conductive surfaces without risking short circuits. At just 6mm height, these are suited for low-profile mounting wh...
LattePanda IOTA 51W PoE Expansion Board (IEEE 802.3bt)
·
Designed specifically for the LattePanda IOTA single-board computer, this expansion board adds IEEE 802.3bt PoE++ power and Gigabit Ethernet data over a single Ethernet cable. It can deliver up to 51W, helping simplify installations where a separate power adaptor would be awkward or where periphe...
Raspberry Pi HAT Hardware Kit
·
Build a neater, sturdier Raspberry Pi stack with this hardware kit for mounting a standard Pi HAT. It is designed for Raspberry Pi 3, 4 and 5 boards, including builds where a larger cooling fan or heat sink needs extra clearance.The included tall 2x20 pin female GPIO header raises the HAT above t...
Leopard Imaging Camera Mounting Hardware Kit
This hardware kit consists of 4 each of M2 style nylon hex nuts and screws. It is designed for use with the Leopard Imaging Camera, but can be used for other mountings as well.This hardware set is identical to what is included in our JetBot kit options.
Standoffs Plastic - (4-40; 3/4; 10 pack)
Nylon standoffs for mounting PCBs in enclosures or elevating boards off work surfaces. These ¾" (19mm) long standoffs are tapped for 4-40 screws and sold in a pack of 10. Key Features Nylon Construction – Non-conductive, won't short circuit boards 4-40 Thread – Standard tapping for 4-40 screw...
Standoff - Nylon (4-40; 3/4; 10 pack)
These nylon standoffs are ¾" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. The black nylon will give your project a very sessy look. Sold in packs of ten. Check below for matching screws.
Clear Acrylic Enclosure + Hardware Kit for Adafruit CLUE
A clear acrylic enclosure designed specifically for the Adafruit CLUE board. Laser-cut to accommodate the TFT display, tactile buttons, and capacitive pads, this minimalist case protects your board while keeping all features accessible. Assembly takes less than five minutes with the included nyl...
Adafruit MagTag Starter Kit - ADABOX017 Essentials
The Adafruit MagTag Starter Kit bundles everything you need to get started with the MagTag WiFi E-Ink display. The ESP32-S2-powered board features a 2.9" grayscale E-Ink screen that retains its image even when power is removed — perfect for low-power IoT dashboards, status boards, and information...
Standoff - Nylon (4-40; 3/8; 10 pack)
These nylon standoffs are 3/8" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. The black nylon will give your project a very sessy look. Sold in packs of 10. Check below for matching screws.
Raspberry Pi 4 DIN Rail ABS Case – Spacious Interior
·
A durable ABS enclosure for the Raspberry Pi 4 Model B, designed for DIN rail mounting in industrial and automation environments. The spacious interior accommodates the Pi along with HATs and add-on boards, while a clear top window lets you monitor status LEDs without opening the case. Manufactu...
Circuit Playground Bolt-On Kit
This bolt-on hardware kit provides M3 standoffs and screws for securely mounting a Circuit Playground Express, Circuit Playground Classic, micro:bit, Gemma M0, Flora, or other small circular/compact boards to your projects, enclosures, and robots. Key Features M3 Brass Standoffs – 12 mm hexago...
LattePanda Mu A380 MXM GPU Carrier Board Kit
·
Build a compact LattePanda Mu-based x86 edge system with discrete MXM graphics and multi-display output. This carrier board kit is designed to bridge the gap between low-power SBCs and larger industrial PCIe expansion systems, making it suitable for edge AI, signage and visual computing projects....
PCB-mount 2x5-Pin Edge Card Connectors - 5 Pack
These 2.54mm pitch edge card connectors are designed for interfacing with compatible PCBs or circuit boards, allowing easy data transmission. They are commonly used in computers as expansion slots for peripheral cards, as well as in game consoles and other electronic systems.What’s included?Packa...
Pan and Tilt Kit (Black Anodized) (no servos)
A black anodised pan-and-tilt assembly designed for horizontal surface mounting. Built using two DFRobot servo brackets, this kit provides two axes of rotation for cameras, sensors, or other payloads on small robots and remote-controlled platforms. The kit includes all necessary mounting hardwar...
DIN Rail Mount Bracket for Arduino UNO R3 / Leonardo
This DIN Rail Mount Bracket provides quick and easy mounting for Arduino, which allows you to conveniently build up your Arduino-related projects. Made of high-quality PVC material, it is durable and fireproof, and well suitable for the boards like UNO R3 and Leonardo. Application Dimension...
Nylon 4-40 Standoff - 3/4 inch
·
This nylon standoff is a simple hardware spacer for raising a PCB off a surface or mounting it neatly inside an enclosure. It is tapped for a 4-40 screw and measures 3/4" long.Use it to give your board clearance from the benchtop, reduce accidental shorts, or create a cleaner mechanical mounting ...
