All Products

SKU: AF-4352

Build a handheld light-up button controller with this complete kit that pairs the Adafruit 4×4 NeoTrellis RGB Driver with a Feather M4 Express inside an elegant laser-cut acrylic enclosure. The 16 silicone buttons each have individually addressable NeoPixels underneath, and the seesaw I2C chip ha...

SKU: AF-4339

This laser-cut acrylic enclosure kit turns your 4×4 NeoTrellis setup into a handheld device with an elegant black and white design and beautifully diffused button illumination. Designed to house any Adafruit Feather board (except FONA) alongside the NeoTrellis RGB Driver PCB. The enclosure inclu...

SKU: AF-4372

This laser-cut acrylic enclosure kit turns your 8×8 NeoTrellis setup (four 4×4 NeoTrellis boards) into a handheld device with an elegant black and white design and beautifully diffused button illumination. Designed to house any Adafruit Feather board (except FONA) alongside four NeoTrellis RGB Dr...

SKU: AF-3938

The NeoTrellis M4 Mainboard combines an ATSAMD51 Cortex M4 processor, a 4×8 grid of NeoPixel-lit elastomer button pads, stereo audio output, microphone input, and a triple-axis accelerometer into one compact, programmable board. Think of it as a button-mashing, light-flashing, tune-making powerho...

SKU: AF-3954

Upgrade your button-pad projects with full-colour NeoPixel backlighting. The NeoTrellis RGB Driver PCB is a 4×4 keypad controller with 16 NeoPixels and an onboard seesaw I2C chip that handles both button scanning and LED driving — all over plain I2C, no NeoPixel pin management required. The boar...

SKU: AF-6433 · MPN: ADA6433

Keep your Adafruit MagTag safe and looking sharp with this custom-designed 3D-printed enclosure. The snap-together two-piece case accommodates all connection ports and features flexible push tabs for the four front buttons, plus an integrated kickstand for tabletop use. Made with an SLA printing...

SKU: AF-4506

The Adafruit 1.3" Colour TFT Bonnet for Raspberry Pi combines a 240×240 IPS TFT display with a 5-way joystick and two pushbuttons on a single plug-and-play bonnet. The display is driven by the ST7789 controller over SPI, delivering vibrant 16-bit colour with wide viewing angles. A Qwiic/STEMMA Q...

SKU: AF-1490

These 6 mm tall tactile switch buttons are momentary normally-open pushbuttons commonly used as input buttons in electronics projects. The extra height makes them useful for projects in enclosures where the buttons need to protrude through the case. They work best when soldered into a PCB but ca...

SKU: AF-4675

A clear acrylic enclosure designed specifically for the Adafruit CLUE board. Laser-cut to accommodate the TFT display, tactile buttons, and capacitive pads, this minimalist case protects your board while keeping all features accessible. Assembly takes less than five minutes with the included nyl...

SKU: AF-802

The Adafruit 1.8" Colour TFT Shield is a plug-and-play display solution for Arduino, combining a bright 128×160 pixel TFT screen with a microSD card slot, 5-way joystick navigation switch, and three tactile buttons. This R3-format shield works with any Arduino or Metro board including the Metro M...

SKU: AF-4028

Get started with CircuitPython using this all-in-one starter kit built around the Adafruit ItsyBitsy M4 Express. The ItsyBitsy M4 packs a 120 MHz ATSAMD51 Cortex M4 processor with floating point support, 512 KB flash, and 192 KB RAM into a compact, breadboard-friendly form factor — more than enou...

SKU: AF-3915

Keep your Circuit Playground Express safe in this snap-together acrylic enclosure. Designed by Ada-friend Mike Doell, this minimal but elegant case turns your board into an electronic snowflake shape with no tools required for assembly. The enclosure provides full access to all buttons, the slid...

SKU: AF-6241 · MPN: ADA6241

A custom-designed snap-on enclosure for the Adafruit Feather RP2040 with DVI Output Port. 3D printed using an SLA process in translucent milky white plastic, it provides a clean, protective case with no visible layer lines or surface imperfections. No screws or glue required — simply snap the Fe...

SKU: AF-2866

Put on your sunglasses before plugging in this shield — 40 eye-blistering RGBW LEDs adorn the NeoPixel Shield for a blast of configurable colour and white. Arranged in a 5×8 matrix, each pixel is individually addressable using just one pin (Digital #6 by default, changeable by cutting a trace). ...

SKU: AF-3800

The Adafruit ItsyBitsy M4 Express is a high-performance microcontroller board powered by the ATSAMD51 Cortex M4 running at 120 MHz with hardware floating point and DSP support. Packed into a tiny 1.4" × 0.7" form factor, it delivers 512 KB Flash, 192 KB RAM, and 2 MB of SPI Flash for CircuitPytho...

SKU: AF-4860

The Adafruit Prop-Maker Starter Kit contains the electronics you need to build a 3D-printed NeoPixel lightsaber with motion-activated lighting and full sound effects. The kit pairs the Feather M4 Express with the Prop-Maker FeatherWing, giving you an accelerometer for swing and hit detection, a C...

SKU: EC-WRF315KIT

A simple 315MHz wireless controller kit consisting of a 4-button RF keyfob remote and a matching receiver module. No programming or microcontroller is required — power the receiver with 5V DC and press a button on the keyfob to activate the corresponding output pin. Uses SC2273-L4 and SC2272-M4 ...

SKU: AF-2870

Put on your sunglasses before wiring up this LED matrix — 64 eye-blistering RGBW LEDs adorn the NeoPixel NeoMatrix for a blast of configurable colour and white. Arranged in an 8×8 matrix, each pixel is individually addressable with just one microcontroller pin, delivering 32-bit colour (8-bit PWM...

SKU: AF-6124 · MPN: ADA6124

This custom-designed 3D-printed enclosure is made specifically for the Adafruit bq25185 USB/DC/Solar Charger with 3.3V Buck board. The snap-together design requires no screws or glue — simply press the two halves together for a secure fit that protects your board during use and transport. The en...

SKU: AF-1332

Punch in your secret key into this numeric membrane keypad. This keypad has 4 buttons, and since every key has its own wire line, no matrix code is required - just treat these like every day switches. The membrane is soft and has a removable paper backing to expose a strong adhesive so you can st...