All Products

SKU: AF-1222

The Adafruit GEMMA V2 is a tiny, coin-sized wearable microcontroller board powered by an ATtiny85 processor. At just 28 mm in diameter, it's small enough to fit into any sewable or wearable project, and affordable enough to dedicate to every build. Program it over USB with the Arduino IDE and bri...

SKU: AF-1849

Get started with wearable electronics using the Adafruit Gemma Sensor Starter Pack. This all-in-one kit includes a GEMMA V2 board, sewable RGB NeoPixels, multiple sensors, a rechargeable battery with charger, and everything you need to build interactive sewable projects — no soldering required. ...

SKU: AF-3501

The Adafruit GEMMA M0 is a tiny, coin-sized microcontroller board designed for wearable electronics and small projects. Despite its quarter-sized footprint, it packs serious power with an ATSAMD21E18 32-bit Cortex M0+ processor, 256 KB of Flash, and 32 KB of RAM — a massive upgrade over the origi...

SKU: AF-1850

Add a touch of sparkle to your wearables with the Adafruit Gemma Sequin Starter Pack. This beginner-friendly kit includes a GEMMA V2 sewable microcontroller, warm white LED sequins, conductive thread, needles, and a coin cell battery holder — everything you need to start sewing glowing electronic...

SKU: AF-1657

Get started with Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic project. There's a GEMMA board, four sewable bright RGB pixels, a battery holder and batteries, 2-ply conductive thread, alligator clips to help you test out your circuit, and a U...

SKU: WS-29380 · MPN: 29380

This 0.71″ round LCD module packs a 160 × 160 pixel IPS display with 65K colours into a tiny 20 × 22 mm footprint. Driven by the GC9D01 controller over a 4-wire SPI interface, it's easy to integrate with Raspberry Pi Pico, ESP32, Arduino, and other microcontrollers using minimal IO pins. The rou...

SKU: AF-1759

Mod your stuffed toy to chirp, meow, or woof! This GEMMA parts pack makes it easy to add simple sounds to any plush toy, and especially the Sew-Your-Own Owl Kit (not included!) A tilt ball switch is used to trigger GEMMA to play a sound of your choosing (or write your own) through a small spea...

SKU: AF-5217

The Adafruit LED Glasses Driver is a slim, Bluetooth-enabled controller board built around the Nordic nRF52840 chipset. Originally designed to drive the Adafruit LED Glasses RGB LED matrix, it also works brilliantly as a compact standalone development board with built-in sensors and STEMMA QT con...

SKU: AF-5255

The Adafruit LED Glasses Starter Kit includes everything you need to build a complete pair of programmable LED glasses. Pair the 116-LED front panel with the Bluetooth-enabled nRF52840 driver board, snap them onto the included fashion frames, and you're ready to create dazzling wearable light dis...

SKU: AF-4197

Add a crisp, paper-like display to your microcontroller project with the Adafruit 2.13" Monochrome eInk Breakout. This 250×122 pixel black-and-white eInk panel delivers excellent daylight readability and retains its image even with power completely disconnected — just like printed paper. An onbo...

SKU: AF-1405

Get started with the fabulous Adafruit Flora platform with this lovely budget kit, just enough to get you started with this fun wearable computer. Included are enough parts to make your first wearable electronic project. There's a Flora motherboard, four ultra-bright chainable RGB pixels, a 3x...

SKU: AF-1758

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making them smaller and easier to use for many projects. Simply connect 3–6 VDC to the ...

SKU: AF-1756

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making them smaller and easier to use for many projects. Simply connect 3–6 VDC to the ...

SKU: AF-1755

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making them smaller and easier to use for many projects. Simply connect 3–6 VDC to the ...

SKU: AF-5510

nOOds are ultra-flexible LED filaments — the same type found inside decorative Edison-style LED bulbs, but available as standalone strips for your own projects. This 300 mm pink nOOd is made of dozens of parallel LED diodes bonded onto a flexible metal backing and coated in coloured silicone. Pow...

SKU: LB-LS0824-V2

This IO expansion board adapter for the micro:bit V2 breaks out all pins to accessible connectors, making it easy to connect sensors, modules, servos, and other peripherals to your micro:bit projects without alligator clips or soldering. The compact, plug-in design makes it a practical addition ...

SKU: AF-3377

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making them smaller and easier to use for many projects. Simply connect 3–6 VDC to the ...

SKU: AF-5228

A raw 1.3" monochrome OLED display module with 128 × 64 pixel resolution, driven by the SH1106G controller over SPI. This is the same display used in the Adafruit MACROPAD RP2040. Key Features 1.3" Monochrome OLED – 128 × 64 pixel resolution SH1106G Driver – SPI interface 16-Pin FPC Connecto...

SKU: AF-911

Yes, this is an adorable miniature television! The visible display measures only 2.0" diagonal, the TFT comes with a NTSC/PAL driver board. The display is very easy to use - simply connect 6-12VDC to the red and black wires, then connect a composite video source to the yellow and black wire. Voil...

SKU: AF-1757

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making them smaller and easier to use for many projects. Simply connect 3–6 VDC to the ...