All Products

SKU: AF-4712 · MPN: 4712

The Adafruit LC709203F Fuel Gauge monitors your single-cell LiPo or Li-Ion battery and reports both voltage and state of charge as a percentage over I2C. It handles the non-linear voltage-to-percentage conversion for you, so your project always knows exactly how much battery is left — just like t...

SKU: AF-5580 · MPN: 5580

The Adafruit MAX17048 LiPoly/LiIon Fuel Gauge and Battery Monitor gives you accurate battery voltage and charge percentage readings for your 1S 3.7–4.2V lithium polymer or lithium ion battery. Instead of guessing remaining capacity from a non-linear voltage curve, this smart sensor does the maths...

SKU: AF-1131 · MPN: 1131

A 500 mm extension cable with a JST-PH 2-pin socket on one end and a matching plug on the other. The colour-coded wires make it easy to verify correct polarity. Compatible with JST-PH terminated battery packs including LiPo, Li-Ion, and AAA battery holders. Key Features JST-PH 2-Pin Connectors...

SKU: DF-DFR0568

This compact DC-DC buck-boost converter automatically steps voltage up or down to deliver a stable 3.3 V output from a wide 2.5–15 V input range. With a maximum output current of 600 mA and ultra-low 180 µA quiescent current, it's perfect for battery-powered projects and embedded systems that nee...

SKU: AF-6391 · MPN: ADA6391

This small accessibility tool helps remove LiPoly and LiIon batteries with JST connectors from a board without tugging on the battery wires.The 3D-printed puller slips over the JST PH connector so you can line it up with the socket and gently lift it out. It is handy for anyone who finds tiny bat...

SKU: DF-DFR0535-1 · MPN: DFR0535-1

Build a compact off-grid power supply for embedded electronics, IoT nodes and low-power projects with this solar power management kit from DFRobot. It combines a Solar Power Manager board for 9V/12V/18V panels with a compact 9V 220mA solar panel.The controller integrates constant-voltage MPPT sol...

SKU: PR-PIM557

This SHIM provides a convenient way of powering your Raspberry Pi Pico from a LiPo/LiIon battery. You can recharge the battery easily by providing power to the Pico's USB port. Solder this neat little square to the pins on the back of your Pico, plug in a suitable lithium-ion/polymer battery ...

SKU: SF-PRT-10401

A simple single-cell LiPo/Li-Ion battery charger based on the MCP73831T charge controller IC. Connect a battery via the JST connector, plug in a Mini-USB cable for power, and the board handles charging automatically with a status LED to indicate progress. Key Features MCP73831T Charge Controll...

SKU: AF-4755 · MPN: 4755

The Adafruit Universal USB/DC/Solar Lithium Ion/Polymer Charger (bq24074) charges 3.7V/4.2V LiPo or LiIon batteries from virtually any power source — USB Type-C, DC adapter, or solar panel — with a wide 5–10V input range. Its near-MPPT solar tracking automatically draws the maximum current availa...

SKU: AF-5612 · MPN: 5612

This SHIM from the Pimoroni Pirates provides a convenient way of powering your Raspberry Pi Pico from a LiPo/LiIon battery. You can recharge the battery easily by providing power to the Pico's USB port, then take your Pico or Pico W project on the go with the battery pack powering your circuitry....

SKU: WS-17674

AI Autonomous Racing Robot Powered by Raspberry Pi 4, Supports DonkeyCar Project, Deep Learning, Self Driving Note: the Raspberry Pi 4 is optional.   SAFETY CAUTIONS Li-ion and Li-po batteries are quite unstable. They may cause fire, personal injury, or property damage, if they're not...

SKU: LB-JST-10

A 10-pack of JST-PH 2-pin SMT right-angle connectors. This is the standard connector used on single-cell LiPo and Li-Ion batteries, making it essential for any battery-powered project. The right-angle orientation and surface-mount pins keep wiring neat and low-profile. Compatible with JST-PH 2-p...

SKU: SF-PRT-10217

If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The SparkFun LiPo Charger Basic is stripped down of all features and just does one thing well - charge 3.7V LiPo cells at a rate of 500mA. It is designed to charge single-cell Li-Ion or Li-Polymer ba...

SKU: DF-DFR0208

If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The Lithium Battery Charger can charge 3.7V LiPo battery at a rate of 500mA per hour. It is designed to charge single-cell Li-Ion or Li-Polymer batteries. Check the datasheet below to see if it will wo...

SKU: DF-DFR0446

In many applications, we will use lithium batteries as our power solutions. In this kind of application, the most two important things are the power boost and battery charger. These two points are a prerequisite for the system. The traditional power boost and battery charge circuit are usually d...

SKU: TB-SB2300

A 14500-size rechargeable lithium-ion battery with 800mAh capacity and 3.7V nominal voltage. The 14500 form factor is the same size as a standard AA battery, making it a common choice for LED torches and other compact devices that accept this cell type. This cell has a nipple (button-top) positiv...

SKU: AF-5397 · MPN: 5397

The Adafruit LiIon/LiPoly Charger BFF is a compact battery charging add-on designed to mount directly onto the back of any QT Py board. It makes portable power simple — plug in a standard 3.7 V/4.2 V lithium battery, and the charger handles the rest via the QT Py's USB-C connection. When USB is ...

SKU: WS-25567

The UPS HAT (D) is a powerful uninterruptible power supply designed for Raspberry Pi, offering seamless charging and power output with dynamic path management. This HAT provides stable 5V output, ensuring uninterrupted operation for your Pi projects. It supports 21700 Li-ion batteries (not includ...