All Products

SKU: DF-DFR0592

The DC Motor Driver HAT is a Raspberry Pi add-on board that drives up to two DC motors via I2C. Built around the TB6612FNG motor driver chip with 1.2 A continuous current per channel (2 A peak), it supports both standard DC motors and motors with encoders through the on-board encoder interface. ...

SKU: SF-ROB-09571

The SparkFun Serial Controlled Motor Driver allows you to control up to two DC motors using a serial command interface. The serial interface is easy to use and it lets the user select an individual motor, the direction, and the desired speed constant (up to 10 different speed from stop to full sp...

SKU: SF-ROB-14451

The SparkFun TB6612FNG Motor Driver breakout can independently control up to two DC motors at a constant current of 1.2 A (3.2 A peak). Each motor channel supports four modes — clockwise, counter-clockwise, short-brake, and stop — controlled via two input signals and a PWM speed input. All pins ...

SKU: AF-3297

The Adafruit DRV8833 is a dual H-bridge motor driver breakout, capable of driving two DC motors bidirectionally or one bipolar/unipolar stepper motor at up to 1.2 A per channel. It's well suited for low-voltage applications, operating from 2.7V to 10.8V motor power. The DRV8833 features built-in...

SKU: SF-ROB-14450

The TB6612FNG Motor Driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes: CW, CCW, short-brake and stop. The two motor outputs (A and B) can be separately controlled, and t...

SKU: DF-DFR0601

This is a dual channel DC motor driver with an extremely small size of of 1.97”×1.97”×0.49”. The module comes with two motor channels that can drive two motors simultaneously, and each channel employs an indicator to show the rotation direction of the motor: blue is forward rotation, red is rever...

SKU: DF-DRI0058 · MPN: DRI0058

This compact DFRobot driver board is made for precise control of brushless DC motors using Field-Oriented Control (FOC). At just 26 x 21.5mm, it is well suited to tight builds where smooth motion, low noise and responsive control matter.SimpleFOCmini supports closed-loop control of motor position...

SKU: PL-4733

The MP6550 from Monolithic Power Systems (MPS) is an H-bridge motor driver IC that can be used for bidirectional control of one brushed DC motor at 1.8 V to 22 V. It can supply up to about 1.7 A continuously and features configurable current sensing and current limiting. Since this board is a car...

SKU: AF-807

Run four solenoids, two DC motors or one bi-polar or uni-polar stepper with up to 600mA per channel using the L293D. These are perhaps better known as "the drivers in our Adafruit Motorshield". If you accidentally damaged the drivers in a shield, you can use one of these puppies to replace it....

SKU: AF-6121 · MPN: ADA6121

The Adafruit TMC2209 Stepper Motor Driver Breakout Board makes controlling stepper motors easy and virtually silent. Using Trinamic's "Stealth Chopper" technology, this driver delivers smooth, quiet microstepping with just two control pins — no timers, PWM, or real-time microcontroller required. ...

SKU: AF-3190

The Adafruit DRV8871 is a single-channel brushed DC motor driver breakout capable of delivering up to 3.6 A peak current with a wide 6.5–45V motor voltage range. Its resistor-set current limiting and built-in PWM support make it straightforward to use with virtually any brushed DC motor. The boa...

SKU: LB-OWL-HBRIDGE

Using the powerful L298N Dual Motor Driver，this module allows full control of two DC Motors or one stepper-motor. Screw Terminals for easy connections；LEDs show power and output status. Requires six digital inputs. Has 4 mounting holes. Specification: Chip: L298N  Maximum Output Curre...

SKU: AF-2348

The Adafruit DC & Stepper Motor HAT drives up to 4 DC motors or 2 stepper motors from your Raspberry Pi, with full PWM speed control. It uses a dedicated PWM driver chip over I2C, so only two pins (SDA/SCL) are needed — leaving the rest free for other I2C devices or HATs. The TB6612 MOSFET motor...

SKU: EC-MCS02930M

This Adruino compatible motor Driver shield is a full-featured products that it can be used to drive 4 DC motor or two 4-wire stepper and two 5v servo. It drive the DC motor and stepper with the L293D,and it drive the servo with arduino pin9 and pin10. Features Be able to drive 4 DC motor and...

SKU: AF-4280

The Adafruit DC & Stepper Motor Bonnet drives up to 4 DC motors or 2 stepper motors from your Raspberry Pi, with full PWM speed control. It uses a dedicated PWM driver chip over I2C, so only two pins (SDA/SCL) are needed — leaving the rest free for other I2C devices or HATs. The TB6612 MOSFET mo...

SKU: IT-IM120417005

MotoMama is an Arduino shield built around the L298N H-bridge driver chip for small motor and robot projects. It can drive two DC motors or one four-wire, two-phase stepper motor.Motor power can be supplied through the onboard power terminal, which can also power the Arduino board. Alternatively,...

SKU: DF-DFR0399

A compact DC micro metal gear motor with a built-in driver that uses the DFRobot Gravity 3-pin interface. Simply connect to a microcontroller and control direction and speed with a single PWM signal — no external H-bridge required. The embedded driver accepts standard servo-style PPM signals, so...

SKU: PL-4035

This compact breakout board for TI’s DRV8874 motor driver offers a wide operating voltage range of 4.5 V to 37  and can deliver a continuous 2.1 A (6 A peak) to a single bidirectional brushed DC motor. The DRV8874 also features integrated current sensing and regulation as well as built-in pr...

SKU: AF-4225

Everything you need (besides the Jetson Nano) to build NVIDIA's JetBot — an open-source AI robot platform. This parts pack includes the motor driver, motors, wheels, and a handy PiOLED display to get your JetBot rolling. The included DC Motor + Stepper FeatherWing provides I2C control for two br...

SKU: AF-4489

Run two solenoids, or a single DC motor with up to 800mA per channel using the super-simple L9110H H-bridge driver. This bridge chip is an 8 DIP package so it's easy to fit onto any breadboard or perfboard.Each chip contains one full H-bridges (two half H-bridges). That means you can drive 2 sole...