All Products

SKU: AF-3424

This chrome-plated rugged metal pushbutton features a built-in RGB LED ring light and a latching on/off mechanism. Press once to latch on, press again to release — unlike momentary buttons, it stays in position. Simply drill a 22mm hole into any panel up to 6mm (1/4") thick and secure with the in...

SKU: AF-915

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal actuator, surroun...

SKU: AF-916

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal actuator, surroun...

SKU: AF-917

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal actuator, su...

SKU: AF-4660

A rugged, chrome-plated latching pushbutton with a built-in RGB LED ring. Drill a 16 mm hole in any panel up to 6.35 mm (1/4") thick and mount it securely — an included rubber gasket provides a water-resistant seal for enclosures. The flat metal actuator latches on press and releases on a second...

SKU: SF-COM-30227 · MPN: COM-30227

The RV-1805-C3 is an ultra-low-power real-time clock module built for efficient, reliable timekeeping in battery-powered electronics. It integrates the crystal (XTAL) directly into a hermetically sealed ceramic package, removing the need for external clock tuning.With a maximum timekeeping curren...

SKU: PH-MMP-0594

Following a successful campaign on IndieGoGo SnowPi the GPIO Snowman for Raspberry Pi is now available! Ideal as a Stocking filler this christmas SnowPi the GPIO Snowman is an ideal kit for people new to Raspberry Pi or even the experienced users. Snow Pi comes as a to solder kit and is target...

SKU: SF-GPS-30018 · MPN: GPS-30018

Built around the u-blox SAM-M8Q module, this compact GNSS receiver is a straightforward way to add location tracking to a project. Plug in USB-C for power and configuration, or use the Qwiic connectors for solder-free I2C integration with compatible boards.The board includes an integrated smart a...

SKU: DF-FIT0951 · MPN: FIT0951

A 40 cm power cable designed to connect SATA devices to the LattePanda Sigma single-board computer. It converts the LattePanda Sigma's PH2.0 4-pin power output to a standard SATA 15-pin female connector, providing both 12 V and 5 V rails for SATA hard drives and other storage devices. Key Featur...

SKU: WS-25553

A 3 MP camera module built around the SmartSens SC3336 sensor, designed for use with LuckFox Pico series boards. The 1/2.8" CMOS sensor delivers high-sensitivity, high-SNR imaging with strong low-light performance, making it well suited for surveillance, computer vision, and night-time monitoring...

SKU: SF-COM-13952

The CD40106BE consists of six Schmitt-trigger circuits. Each circuit functions as an inverter with Schmitt-trigger action on the input. The trigger switches at different points for positive- and negative-going signals. The difference between the positive-going voltage (VP) and the negative-going ...

SKU: SF-COM-10926

A 1N5819 Schottky diode rated at 1A and 40V. Schottky diodes are characterised by their low forward voltage drop (typically ~0.3V) and very fast switching speed, making them ideal for flyback protection on motor driver circuits, reverse polarity protection, and high-frequency rectification. Spec...

SKU: SF-COM-29757 · MPN: COM-29757

This compact Schottky diode is designed for efficient rectification where low forward voltage, low leakage and fast switching are important.It suits circuits that need higher current operation in a small surface-mount part, including designs operating at higher temperatures above 85°C.The manufac...

SKU: JU-W-LP232

Are you a proud supporter of science? Do you believe in its potential to make the world a better place? This enamel pin is a subtle reminder to always seek out evidence-based solutions and to trust in the power of scientific research. It's a great conversation starter and a way to connect with...

SKU: JU-W-LP233

Do you remember your first science project, the one that made you explode with glee!?  Science is not only about facts and figures, it's also about understanding how the world works, and this is where the magic comes in. Science can help us to unlock the secrets of the universe, or bake ...

SKU: AF-6051 · MPN: ADA6051

Add magnetic sensing to your project with this breakout built around the Texas Instruments DRV5032 digital Hall effect sensor. Its digital output changes when the magnetic flux density threshold is crossed, making it useful for detecting magnets, position, lids, doors, rotations and other simple ...

SKU: AF-5651

An I2C breakout board for the RDA5807M FM radio chip, designed by ScoutMakes as a beginner-friendly introduction to electronics and wireless communications. Tune into FM stations, display RDS data (station and song names), and control everything from an Arduino or CircuitPython sketch. The board...

SKU: LB-00333

Scratch is the wildly popular educational programming language used in millions of homes and schools worldwide to create interactive art, stories, games, simulations, and music videos.With "The Scratch Activity Cards," a colorful 52-card deck, kids work through beginner-friendly coding projects. ...

SKU: SF-PRT-28863 · MPN: PRT-28863

This simple pair of screw clamps is handy for securing parts of your project during mounting, helping keep cables or assemblies neatly held in place.They are the same style of clamps supplied with the Weather Meter Kit, making them useful as replacements, spares, or for similar outdoor sensing an...

SKU: LB-KEY-SCREW

These handy little screwdrivers can be used with our E-Textile boards to add and remove the M1.4 screws to access the coin cell battery.The screwdriver comes on a handy keyring so you can carry it round.These are also great for doing glasses repair and access to phones.