All Products

SKU: AF-798

Warning: This is a US-plug adapter and is not certified for use in Australia. Only purchase if you are using it outside Australia or with an appropriate plug adapter. A regulated 12V DC switching power adapter delivering up to 1000mA (1A). The slim profile fits into power strips without blocki...

SKU: AF-248

A 6×AA battery holder with a 5.5mm/2.1mm DC barrel plug, ready to power Arduino boards and other electronics with a standard DC jack. Use alkaline AAs for approximately 9V at 3000–4000mAh, or rechargeable NiMH cells for 7.2V at ~2000mAh. The 9V alkaline output is ideal for boards with a 5V volta...

SKU: AF-276

This FCC/CE certified and UL-listed switching power supply delivers a clean, regulated 5V DC output at up to 2A (2,000mA) via a standard 5.5×2.1mm DC barrel jack. It accepts 110–240V AC input and is suitable for powering LED strips, motors, and other current-hungry 5V devices. Key Features Out...

SKU: SF-KIT-15716 · MPN: KIT-15716

This passive adapter lets a Teensy development board connect to the standard Arduino 1.0 (R3) shield footprint, making it easier to reuse existing Arduino shields without a breadboard full of jumper wires.Solder your Teensy board, sold separately, to the marked footprint on the adapter, then plug...

SKU: AF-1466

This UL-listed switching power supply delivers a clean, regulated 5V DC output at up to 4A (4,000mA / 20W) via a standard 5.5×2.1mm centre-positive DC barrel jack. It accepts 110–240V AC input and is ideal for powering LED matrices, NeoPixel strips, and other high-current 5V projects. Key Featur...

SKU: DF-DFR1136 · MPN: DFR1136

This DFRobot motor driver carrier board is purpose-built for the UNIHIKER M10, featuring a tilted edge connector slot that positions the screen at an optimal viewing angle. It integrates a dual 3 A DC motor driver with separate motor power, plus onboard RGB LEDs and infrared transmitter/receiver....

SKU: WS-19485

4G HAT FOR RASPBERRY PI Enabling LTE Cat-4 4G / 3G / 2G Communication & GNSS Positioning Based on SIM7600G-H, Global Band Features At A Glance Connected via pogo pin or MicroUSB connector Dedicated pogo pin for Raspberry Pi Zero/Zero W MicroUSB connector for other Raspberry Pi boards or...

SKU: AF-3546

A passive adapter with a 1st-generation MagSafe plug on one end and a 5.5 mm / 2.1 mm DC barrel jack (centre-positive) on the other. It lets you connect a 15–20 VDC barrel-jack power supply to devices that use the original MagSafe connector — useful for bench testing, custom power setups, or repl...

SKU: AF-4090

The Adafruit USB C Breakout Board (Downstream Connection) gives you easy access to all the pins on a USB Type-C connector, configured for downstream device use. Two 5.1K resistors on the CC1 pins signal the upstream host to provide 5V at up to 1.5A, mimicking classic USB 2.0 behaviour. For most ...

SKU: AF-1833

This breakout board gives you easy access to all 5 pins of a USB Micro-B connector via standard 0.1" header pins. It's a simple way to add USB 5V power to a project, interface with a USB-capable microcontroller, or prototype custom USB connections on a breadboard. The board uses a micro-AB conne...

SKU: AF-3456

This 5×AA battery holder delivers approximately 7.5V from five AA batteries, terminated with a 2.1mm DC barrel plug (centre positive). It provides the ideal voltage for Arduino boards and other development boards with onboard 5V regulators, which typically need 1–2V of headroom above their output...