All Products

SKU: AF-1831

This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 100K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will shift on its own. We like this one because the legs are 0.2" apart with pin-poi...

SKU: AF-5128

The Adafruit MacroPad RP2040 Starter Kit is a complete programmable 3×4 macro keyboard powered by the Raspberry Pi RP2040 microcontroller. This all-in-one kit includes the MacroPad board, key switches, keycaps, enclosure, and hardware — ready to assemble with no soldering required. Program it wi...

SKU: AF-5632 · MPN: ADA5632

This breakout makes it much easier to prototype with external QSPI flash on modern microcontroller platforms such as RP2040, ESP32, RT10xx and STM32 designs. It converts a wide 8-SOIC flash package into a breadboard-friendly 0.3" wide DIP format, which is handy when you want to test different fla...

SKU: AF-4054

This panel mount cable will allow you to enclose a device that has an HDMI port. Perfect for placing your project in a secure box. Both ends have HDMI connectors, an extension cord if you will.What's special about this, you ask? It's a Snap-In Panel Mount Cable - much easier than a classic panel ...

SKU: AF-6126 · MPN: ADA6126

Here is a cute and minimal enclosure for your Adafruit bq25185 USB / DC / Solar Charger with 5V Boost Board to keep it safe during use and transport. This case has been custom-designed and 3D printed to accommodate all the connectors. No screws or glue are required; simply snap the board into the...

SKU: SF-PRT-00091

A classic 9V battery snap connector terminated with a 2-pin polarised Molex connector. Ideal for quick-connect battery power in breadboard and prototyping setups. Key Features Molex Terminated – 2-pin polarised connector for secure, reversible connections Cable Length – 5 inches (approximatel...

SKU: PR-PIM373

The VL53L1X Time of Flight sensor breakout uses a low-power laser to measure distances with excellent accuracy and speed. With a detection range of 4 cm to 4 metres and up to 50 Hz sampling frequency, it's ideal for proximity sensing, presence detection, and collision avoidance on robots. This b...

SKU: SF-ROB-10391

A linear push-type solenoid rated for 36 V DC that also works well at 12 V. Solenoids produce linear motion for pushing, pulling, or actuating switches and levers. This unit has a measured throw of approximately 10 mm. Key Features Linear Push Solenoid – For push, pull, and actuation applicati...

SKU: DF-FIT0495-E

This compact metal DC geared motor features a 99:1 metal gear reduction for high torque output in a small form factor. With a maximum torque of 2.5kg·cm, it's built for robotics, automation, and mechanical projects requiring reliable, durable performance. Specifications Rated Voltage: 6V Oper...

SKU: SF-ROB-10848

These steppers have a threaded shaft, which allows them to be used as a linear actuator. As the motor runs, it moves along the shaft at a specific rate of 1cm per 5 full rotations. These are a good choice for linear motion where precision and repeatability are important. Note: It looks like the ...

SKU: DF-FIT0577

This DC gearmotor are now in the status of Pre-order and will ship in the end of Jun. This DC gearmotor has an integrated M3*20mm threaded rod as its output shaft, turn it into a linear actuator. 6V rated voltage, the no-load speed could arrive 98RPM, equivalent to 1.1mm/s. The brass facepla...

SKU: SF-BOB-19626

The SparkFun 8 Channel Level Shifter Breakout features the TXS01018E™ 8-bit, bi-directional logic level translator from Texas Instruments. This board allows you to easily shift logic between devices running at different common microcontroller voltages such as 1.8V, 3.3V and 5V. The TXS0108E ca...