All Products

SKU: SF-WRL-21604 · MPN: WRL-21604

The BMD-34 series is a compact, surface-mount multiprotocol RF module for low-power embedded designs needing Bluetooth 5, Thread or Zigbee connectivity at 2.4 GHz. It is based on the Nordic nRF52840 and combines an Arm Cortex-M4 with FPU, integrated radio and hardware cryptographic engine in a re...

SKU: SF-WRL-25134 · MPN: WRL-25134

Build connected sensor nodes, data loggers and battery-powered IoT projects around Raspberry Pi’s RP2350 microcontroller. This Thing Plus board adds wireless connectivity, extra memory and the familiar Feather-compatible footprint in a compact development platform.The RP2350 can run two selected ...

SKU: AF-2674

If you've been diggin' our monochome OLEDs but need something bigger, this display will delight you. These displays are 2.7" diagonal, and very readable due to the high contrast of an OLED display. This display is made of 128x64 individual white OLED pixels, each one is turned on or off by the co...

SKU: AF-4718

The Adafruit SPI Non-Volatile FRAM Breakout provides 2 Mbit (256 KBytes) of ferroelectric RAM (FRAM) storage over SPI. FRAM combines the non-volatile retention of flash with the instant read/write speed of SRAM — no page writes, no block erasing, and each byte can be written 10 trillion times wit...

SKU: AF-1463

Round and round they go! 16 ultra-bright smart RGB NeoPixels are arranged in a circle with a 44.5 mm (1.75″) outer diameter. Each LED is individually addressable from a single microcontroller pin, delivering 24-bit colour with ~18 mA constant-current drive for consistent brightness regardless of ...

SKU: EC-CDD8266KIT

This kit includes a serial WiFi transceiver ESP8266 module and a breadboard adapter to make it convenient to use ESP8266 module with breadboard.ESP8266 is a highly integrated chip that has Integrated TCP/IP protocol stack. It offers a complete and self-contained Wi-Fi networking solution, allowin...

SKU: SF-KIT-18006

The Elektor MIT App Inventor Bundle is a kit built to help learn about developing apps for Android compatible mobile devices using the MIT App Inventor online development environment. MIT App Inventor projects can be in either standalone mode or use an external processor. In standalone mode, the ...

SKU: AF-5228

A raw 1.3" monochrome OLED display module with 128 × 64 pixel resolution, driven by the SH1106G controller over SPI. This is the same display used in the Adafruit MACROPAD RP2040. Key Features 1.3" Monochrome OLED – 128 × 64 pixel resolution SH1106G Driver – SPI interface 16-Pin FPC Connecto...

SKU: LB-LS0537

The DT-06 is a compact Wi-Fi-to-TTL serial module based on the ESP8285 — essentially an ESP8266 with 1 MB of built-in SPI flash. It provides a simple way to add Wi-Fi connectivity to any microcontroller project via a UART serial interface, using AT commands or custom firmware. The module support...

SKU: EC-ESP11002R

A WiFi-controlled relay module designed for ESP-01 or ESP-01S modules (based on the ESP8266). The relay is controlled via GPIO0 with a low-level trigger, allowing you to switch mains-powered devices on and off wirelessly from a phone or any WiFi-connected device. APP and LUA source code are provi...

SKU: AF-501

This 5V 1A USB power supply provides clean, regulated power for microcontrollers, development boards, and USB-charged devices. It accepts 110–240V AC input and outputs via a USB Type-A port, so you simply plug in whatever USB cable your project needs. The supply is intentionally designed to outp...

SKU: LB-LS0205

A WiFi-controlled relay module based on the AI-Thinker ESP-01S (ESP8266). It lets you switch AC or DC loads remotely over WiFi, making it a simple building block for smart home automation, IoT switching, and remote control projects. The module comes pre-loaded with demo firmware — supply 5V DC p...