All Products

SKU: DF-DFR0299

Sing for the moment! The DFPlayer Mini is a small and low cost MP3 module player with an simplified output directly to the speaker. The module can be used as a stand alone module with attached battery, speaker and push buttons or used in combination with an Arduino UNO or any other with ...

SKU: DF-DFR1173 · MPN: DFR1173

This compact voice prompt module integrates an intelligent MP3 playback chip with a 1 W speaker in a tiny 30 × 11 mm package. It supports MP3, WAV, and WMA hardware decoding with 16 MB of on-board storage that retains files even when power is lost. Control playback via the built-in button (short...

SKU: DF-DFR0782

An evaluation board for a dual-mode Bluetooth 5.0 module that handles both wireless audio and serial data pass-through simultaneously. It can play audio from U-disk or TF card, stream audio over Bluetooth, handle Bluetooth call control, and run BLE or SPP data pass-through — all at the same time,...

SKU: EC-ASA46530A

DFPlayer Mini is a compact and inexpensive MP3 module that can be connected directly to the speaker. Module can be used alone with battery power supply, speaker and keypad, or through the serial port control, as the Arduino UNO or any microcontroller with a serial port module. The module itself p...

SKU: SF-BOB-00544

Breakout board for the microSD socket that is not much bigger than your fingernail. Compatible with the SPI interface found on any SD card, this tiny form factor was created for cell phone storage and is perfect for your next MP3 project! Board comes fully assembled and tested. The bare socket...

SKU: DF-DFR0534

Do you always feel like the DIY work is boring, not attractive or no vitality when you design it by yourself? This new Gravity MP3 voice module produced by DFRobot can solve these problems. This module can store 8MB audio files, which means it can store more than 200 audios for your choice, sup...

SKU: DF-TEL0108

This Bluetooth audio receiver module supports wireless streaming, USB flash drive, and TF (microSD) card playback. It decodes MP3, WMA, WAV, and lossless FLAC audio formats, with a built-in pre-amp output capable of driving headphones or a small 3 W speaker directly. Powered by 5 V DC via Micro-...

SKU: AF-6250 · MPN: ADA6250

The Adafruit PCM5102 I2S DAC converts digital I2S audio into excellent stereo line-level output through a 3.5mm jack. With an impressive 112dB signal-to-noise ratio and no MCLK or I2C configuration required, simply pipe I2S data in and get audiophile-grade analogue audio out. The PCM5102 accepts...

SKU: AF-6251 · MPN: ADA6251

The Adafruit PCM5100 I2S DAC converts digital I2S audio into clean, high-quality stereo line-level output through a 3.5mm jack. With 100dB signal-to-noise ratio and no MCLK or I2C configuration required, simply pipe I2S data in and get great-sounding analogue audio out. The PCM5100 accepts 16, 2...

SKU: LB-LS6923

This compact voice recording box lets you record up to 2 or 4 minutes of audio and play it back at the press of a button. It's a simple, self-contained module — no soldering or programming required — making it perfect for adding custom sound to DIY projects, gifts, and props. Operation is straig...

SKU: SF-DEV-13743

The SparkFun Level Shifting microSD Breakout is quite similar to the SparkFun microSD Transflash Breakout, but with the included level shifting hardware, this board allows you to utilize a microSD card at Arduino’s SD library’s top speed on a 5V system. With this small breakout board, that is not...

SKU: SF-COM-11025

VS1063 is an easy-to-use, versatile encoder, decoder and codec for a multitude of audio formats. They can be hard to get hold of but we’ve got them! The VS1063 contains a high-performance, proprietary, low-power DSP core as well as ROM memory, 16KiB instruction RAM and up to 80 KiB data RAM for...

SKU: SF-PRT-00127

Do you need a lot of space? But you need it in the size of your pinky nail? microSD (uSD) is here to save the day. TransFlash has now completed standards certification and is now known as microSD. Compatible with the SPI interface found on any SD card, this tiny form factor was created for ...

SKU: DF-DFR0664

A 2.0" IPS TFT LCD display breakout with 320×240 resolution (RGB565), driven by the ST7789V controller. The wide 80° viewing angles in all directions ensure clear visibility, and the SPI interface makes it compatible with a broad range of microcontrollers including Arduino Uno, Leonardo, ESP32, E...

SKU: DF-DFR0649

A 1.54-inch IPS TFT LCD breakout with 240×240 resolution, 16-bit colour (RGB565), and an onboard microSD card slot for storing and displaying images. The ST7789 driver communicates via SPI or DFRobot's GDI interface for plug-and-play connectivity with compatible main controllers. Powered by 3.3–...

SKU: EC-CCB25011M

This is a bluetooth audio receiver module with usb and TF card decoding. Usually it’s can be used as a mp3 player, just a TF card and DC 5V power supply. It has five buttons for you to change mode or achieve other audio control like volume adjustment. It has two modes : music mode and bluetooth d...

SKU: DF-DFR0719

A compact Bluetooth 5.0 audio receiver board that turns any wired speaker into a wireless one. Simply connect power (3.7–24V) and wire up your speaker — pair it with your phone and start streaming music wirelessly. The board features auto-reconnect, so it automatically pairs with the last connect...

SKU: DF-DFR0720

This is a small size and cost-effective Bluetooth 4.2 Audio Receiver module with dual 5W power amplifier circuits. It supports auto-reconnect and can be powered by micro USB or 3.7V lithium battery. The module can be turned into a stereo Bluetooth speaker when connected with two speakers. Also, y...

SKU: WS-25376

Full metal body · Onboard ESP32-WROOM-32 · Multiple host support The WAVE ROVER is a rugged, all-metal 4WD robot chassis for makers, students and researchers who want a capable mobile platform without building one from scratch. Its entire codebase is open source, it ships with an onboard ESP32 co...

SKU: AF-1902

The SmartLED Shield (V4) provides a simple, solder-free way to connect a Teensy 3.2, Teensy 3.5, or Teensy 3.6 to HUB75 RGB LED Matrix Panels. Just plug in your Teensy, connect your panel, and start displaying graphics, patterns, or animated GIFs using the SmartMatrix Library. The shield include...