All Products

SKU: AF-2667

Chip Quik SMD291 tack flux in a convenient 10 cc syringe with plunger and dispensing tip. This synthetic no-clean flux is ideal for all rework, soldering, desoldering, and reflow applications — it stays where you apply it without running across the PCB. Suitable for both leaded and lead-free sol...

SKU: AF-3468

The Chip Quik No-Clean Liquid Flux Pen is great for all rework, solder, de-solder, and reflow applications! In particular this one is from the rework-champs at Chip Quik. Liquid flux helps solder to "cling" to metal by removing oxide buildup. It also helps spread out solder by red...

SKU: SF-KIT-11835

The SparkFun Gram Piano Kit is a beginner-friendly soldering project that assembles into a working capacitive-touch musical keyboard. Once built, the piano plays a full octave of notes through touch-sensitive keys — no mechanical switches required. Pre-installed firmware allows melody playback a...

SKU: DF-SEN0337

TOF Sense is a TOF-based (Time of Flight) laser ranging sensor that offers 1cm-5m detection range, 1mm resolution, ± 1.5cm error, and 10Hz data update frequency. The sensor supports 15 ° ~ 27 ° adjustable FOV, UART and CAN communication (selected by setting). Besides, it allows users to actively ...

SKU: DF-FIT0230

A tube of leaded solder wire with 2% silver content. The compact tube packaging makes it easy to hold while soldering, keeping your fingers safely away from the iron. Lightweight and portable at just 17 g, with approximately 3 m of solder wire. Specifications Composition: Sn 62%, Pb 37%, Ag 2%...

SKU: SF-TOL-09161

This is your basic spool of leaded solder with a 63/37 water soluble resin core. 0.031" gauge and 100 grams. This is a good spool for more advanced users that should last 6-12 months depending on how often you solder.Mix: 63% Sn / 37% Pb

SKU: SF-TOL-09317

This is a solderer’s best helper, the third hand. Comes with a heavy base, two alligator clips, a soldering iron holder, and a good magnifying glass. Note that we don’t normally need a third hand. It’s nice, but soldering flat on a table works just fine. Then again, the desk is starting to loo...

SKU: LB-LS0866

This Nano Multi-Function expansion board is designed especially for Arduino Nano Lead out all digital IO port and analogue IO port, each one with standard positive and negative power interface. Lead out the I2C interface of mainboard for convenient connection.Increasing the DC power supply i...

SKU: ET-1734943

Description: This 1m Cat5 lead is perfect for all your Raspberry Pi networking needs.   Features: LEAD, CAT 5E, 1M, BLACK Connector Type A: RJ45 Plug Connector Type B: RJ45 Plug Cable Length - Imperial: 3.28ft Cable Length - Metric: 1m Jacket Colour: Black Cable Assembly Type: Network ...

SKU: AF-3399

For many years, instructors and teachers have asked us to come up with a better way to teach programming and electronics. We have worked on Circuit Playground Express for over a year to come up with a board that is powerful, beautiful, fun, and perfect for teaching Code.org CS Discoveries Circ...

SKU: TB-WH5682

A 5-metre roll of 2:1 ratio heatshrink tubing in black, with a 3 mm pre-shrink diameter. Shrinks to half its original size when heated, providing insulation, strain relief, and protection for solder joints, wire splices, and cable connections. Supplied in a neat box for workshop storage. Shrink ...

SKU: AF-1798

A 2.5mm stereo (TRS) plug connector for building or repairing custom audio cables. The durable metal construction and flexible spring strain relief ensure a long-lasting, professional result. The 2.5mm plug is a less common size than the standard 3.5mm headphone jack, but is widely used in hands...

SKU: SF-DEV-13814

This is 12 meters of smooth conductive thread spun from stainless steel fiber and wound on a plastic bobbin. Use it to sew up all of your e-textile projects. This small bobbin is a great way to get into wearable electronics without the upfront cost of buying an entire spool of thread. Close to...

SKU: AF-2324

The Adafruit Ultimate GPS HAT adds high-quality GPS and GLONASS positioning to your Raspberry Pi. Built around a PA1616D module, it provides precise location data and a built-in real-time clock (RTC) with coin cell backup — perfect for outdoor projects, time synchronisation, and location-aware ap...

SKU: TB-WQ7407

Connect DVI-D to HDMI systems.   Specifications Audio/Video Signal Type HDMI Lead Output Connection Plug Output Quantity 1pc Lead Output Type DVI-D Input Quantity 1pc Lead Input Connection Plug Lead Input Type HDMI Directional Length of Lead 1.5m Quality of lead Stand...

SKU: LB-LS5165

A compact TT gearmotor with a 48:1 gear ratio, pre-wired with a 15 cm female JST PH 2.0 connector for plug-and-play integration. TT motors are a popular and affordable choice for small robotics projects, offering a good balance of torque and speed in a lightweight, standardised form factor. The ...

SKU: SF-PRT-28007 · MPN: PRT-28007

Add a bit of protection and a cleaner finish to your Alchitry board with this standoff hardware. It is designed for use with compatible Alchitry boards, helping lift the PCB off your work surface or enclosure base.The bolts protrude about 2mm below the board, which is just further than the lowest...

SKU: AF-261

Red and black tinned wires with a 2-pin JST PH connector on the end. 4" / 100mm long. Matches up nicely with our Lipoly chargers! We have the socket 'mating' version of this cable over here, as well as an 'extension' cable that has one of each soldered together. If you want a switch in t...

SKU: DF-FIT0491

INTRODUCTION   This DC gearmotor has an integrated M4*55mm threaded rod as its output shaft, turn it into a linear actuator. 6V rated voltage, the no-load speed could arrive 150RPM, equivalent to 1.75mm/s. The brass faceplate has two mounting holes threaded for M1.6 screws (1.6mm diame...

SKU: TB-WC7724

USB A to USB Micro B lead. Specifications Quality of lead Standard Directional Output Quantity 1pc Output Type ...