All Products

SKU: LB-00103

A high-quality 840-point solderless breadboard with ABS housing and brass contact clips for reliable connections. The classic beige colour gives it a retro look while delivering solid performance for prototyping. Key Features 840 Tie Points – 640 terminal strip + 200 power distribution strip ...

SKU: DF-TEL0111

INTRODUCTION   The ESP32 WiFi and Bluetooth chip is the latest generation of Espressif products. It has a dual-core 32-bit MCU, which integrates WiFi HT40 and Bluetooth/BLE 4.2 technology inside. Compared to the arduino ESP8266 (the previous generation), the ESP32 has a significant ...

SKU: DF-FIT0269

A 10-pack of M3 × 30mm low-profile hex head cap screws with matching nuts. The hex socket drive provides a more secure fastening than standard Phillips or slot-head screws, and the low-profile head sits flush for a cleaner finish. Key Features Hex Socket Drive – Secure fastening with a hex (Al...

SKU: EF-EF03409

ELECFREAKS Power:bit is a kind of micro:bit extension board with minimum size. It is powered by two 2025 button batteries and carries a buzzer on the board

SKU: AF-6359 · MPN: ADA6359

This breakout lets you add an ideal diode to a higher-current DC power path without the usual forward voltage drop of a standard diode. It is designed for 3~23V DC supplies and up to 5A, using the LM73100's back-to-back FETs to keep current flowing in one direction while wasting far less power as...

SKU: LB-LS3938

This terminal block breakout module comes fully assembled and soldered, ready for use with Raspberry Pi boards.It is compatible with Raspberry Pi 1 Model B+, Pi 2 Model B, Pi 3 Model B, Pi 3 Model B+, Pi 4 Model B, Pi Zero, and Pi Zero W.The module features 2.54 mm (0.1″) pitch terminal blocks su...

SKU: PL-1120

A 200:1 plastic gearmotor with a 90-degree output shaft, offering a compact and affordable solution for small robot designs. The low-current brushed DC motor is well-suited for use with common motor drivers, and the recommended operating voltage range is 3–12V. The gearbox is fully enclosed and ...

SKU: SF-PGM-30117 · MPN: PGM-30117

This handheld tool configures REV Smart Robot Servos (SRS) and tests standard RC servos without needing a separate controller. It is built for quick setup at the bench, in the workshop or in a competition toolkit.For SRS units, it gives direct access to operating modes such as continuous rotation...

SKU: DF-FIT0415

This lightweight nylon pan-and-tilt bracket lets you mount a small camera, sensor, or other module on two servos for full two-axis movement. Compatible with most 9–12 g micro servos, it's a quick way to add directional control to robots, drones, and FPV rigs. Key Features Two-Axis Pan & Tilt –...

SKU: AF-1872

This 8 MHz ceramic resonator is a breadboard-friendly oscillator with built-in load capacitors, making it a simple drop-in timing source for microcontrollers. With 0.5% accuracy, it's well suited for everyday electronics, UART baud-rate generation, and general microcontroller clocking. The 3-pin...

SKU: AF-2717

The TCA9548A 1-to-8 I2C multiplexer solves the common problem of needing multiple I2C devices with the same address on a single bus. It acts as a gatekeeper, routing I2C traffic to any of its eight downstream channels on command. Simply write a single byte to the multiplexer's I2C address (defau...

SKU: AF-2442

Need to make a tiny robot? This little micro servo rotates 360 degrees fully forward or backwards, instead of moving to a single position. You can use any servo code, hardware or library to control these servos. Good for making simple moving robots. Comes with five horns and attachment screw...

SKU: DF-FIT0348

This industrial-grade pH combination electrode features a sensitive glass membrane with low impedance, delivering fast response times, good thermal stability, and excellent reproducibility across the full 0–14 pH range. The Ag/AgCl gel electrolyte reference system provides a stable half-cell pote...