All Products

SKU: DF-SEN0468

This is a sensor that detects chlorine concentration and supports three output modes: analog, I2C, and UART. The probe has been calibrated at the factory, which can quickly and accurately measure the concentration of chlorine in the environment. Can be widely used in the detection of chlorine in ...

SKU: DF-SEN0474

This is a sensor that detects hydrogen chloride concentration and supports three output modes: analog, I2C, and UART. The probe has been calibrated at the factory, which can quickly and accurately measure the concentration of hydrogen chloride in the environment. Can be widely used in the detecti...

SKU: WS-25288

Long-wave IR Thermal Imaging Camera Module, 80×62 Pixels, 45°FOV, Available with 40PIN GPIO Header or Type-C PortLong-wave IR Thermal Imaging Camera Module 80×62 Pixels IR Array  Small Size | Non-contact | Motion Detection Features at a glance This is a long-wave IR ...

SKU: DF-SEN0221

The Hall Angle Sensor is a miniature 360 degree sensor which works based on the principle of the Hall effect. It is compatible with the DFRobot Gravity sensor interface, and works with a 5V DC power supply. The analog output is also 0~5V so it can work directly with Arduino. The Hall an...

SKU: DF-SEN0159

The Gravity CO2 Gas Sensor uses an MG-811 electrochemical sensing element to detect carbon dioxide concentration in the air. The output voltage decreases as CO2 concentration increases, and an onboard potentiometer lets you set a threshold for a digital on/off signal output. An onboard heating c...

SKU: DF-SEN0043

An analog ambient light sensor based on the TEMT6000 detector, which has a spectral response closely matching the human eye with very low IR sensitivity. It outputs an analog voltage proportional to the ambient light level, making it easy to read with any Arduino or microcontroller analog input. ...

SKU: DF-SEN0192

INTRODUCTION The microwave sensor applies the Doppler effect to detect moving objects using microwaves. This differs from the method used by a regular infrared (IR) sensor as microwave is sensitive to a variety of objects that are microwave-reflective, and its sensor...

SKU: DF-DFR0076

This Gravity analog flame sensor detects fire and infrared light sources in the 760–1,100 nm wavelength range. With a 60° detection angle and analogue output proportional to flame distance, it's widely used in firefighting robots, fire alarm projects, and other safety applications. The Gravity i...

SKU: DF-DFR0556

A 16×2 character LCD display module from DFRobot's Gravity series, connecting to your Arduino or microcontroller via a simple I²C interface — just two data wires instead of the many parallel connections a standard LCD1602 requires. Compatible with both 3.3V and 5V, with no contrast adjustment nee...

SKU: DF-SEN0610 · MPN: SEN0610

##Introduction The Gravity: C4001 millimeter-wave presence sensor, operating at a wavelength signal of 24GHz, boasts a horizontal detection range of 100°, a presence detection range of 8 meters, and a motion detection and ranging range of 12 meters. It utilizes the Gravity interface (PH2.0) and s...

SKU: DF-SEN0189

The Gravity Analog Turbidity Sensor measures water clarity by detecting the level of suspended particles. It works by measuring light transmittance and scattering rate, which change with the amount of total suspended solids (TSS) in the water. The sensor provides both analogue (0–4.5V) and digit...

SKU: DF-DFR0554

The Gravity I2C 16×2 LCD features RGB font colours on a black background, allowing you to display text in any of 16 million colour combinations. Using the Gravity I2C interface, only two data lines are needed for both communication and backlight control. The display supports 2 rows of 16 charact...

SKU: DF-FIT0514

These wire offers you the best way to connect sensors and actuators to your LattePanda! They are specially designed for LattePanda and DFRobot Gravity Sensors. It compatible with a wide range of Gravity sensors and is easy to connect thanks to the unique anti-reverse-polarity design. It incl...

SKU: DF-DFR0557

The Gravity I2C LCD1602 is a 16×2 character LCD display module from DFRobot's Gravity series, redesigned with a clean modern look and simplified I2C interface. It eliminates the need for contrast adjustment, retains backlight control, and is compatible with both 3.3 V and 5 V systems — making it ...

SKU: DF-DFR0555

The Gravity I2C LCD1602 is a 16×2 character LCD display module with a blue backlight and white text. It communicates over I2C, requiring only two data pins instead of the many parallel connections of a traditional LCD1602. The module is compatible with both 3.3V and 5V systems, and the contrast i...

SKU: DF-DFR0028

This is an arduino tilt sensor. It is used to detect orientation. Inside the sensor, there is a ball that make contact with the pins when the case is upright. Tilt the sensor over and the balls don't touch, thus not making a connection. Here is the principle of tilt sensor to illustrate how i...

SKU: AF-5913 · MPN: ADA5913

The Adafruit STEMMA Reflective Photo Interrupt Sensor uses a TCRT1000 right-angle optical module to detect reflective surfaces. An onboard IR LED emits light, and when an object reflects it back to the IR phototransistor, the output pin drops from high toward 0V — making it easy to detect the pre...

SKU: DF-DRI0056 · MPN: DRI0056

This Gravity haptic driver module is built for Linear Resonant Actuators (LRAs), turning simple I2C commands into crisp tactile feedback for interactive projects. It is powered by the TM6605 driver chip and supports LRA resonant frequencies from 140Hz to 220Hz.The module includes 44 built-in vibr...

SKU: DF-DFR0996

A Magnetic latching relay is a new type of relay.  It features low power dissipation and noiseless.  Unlike other non-latching relay, the latching relay needs two digital pulse signal to switch ON/OFF state. This DFRobot Gravity: magnetic latching relay is compatible with most...

SKU: DF-SEN0321

The Gravity IIC Ozone Sensor measures ozone (O₃) concentration from 0 to 10 ppm with 10 ppb resolution using an electrochemical sensing element. Factory-calibrated for accurate readings out of the box, it connects via I2C through DFRobot's Gravity 4-pin interface. Compatible with Arduino, ESP32,...