All Products

SKU: AF-3131

The Adafruit 0.54" Quad Alphanumeric FeatherWing Display in yellow adds a bright, easy-to-read 4-character 14-segment LED display to any Feather microcontroller. Each character can show full alphanumeric text (A–Z, 0–9) plus symbols, making it ideal for clocks, sensor readouts, status messages, a...

SKU: AF-3957

The Adafruit CRICKIT HAT is a robotics and electronics driver board that plugs directly onto any Raspberry Pi with a 2×20 GPIO header. It adds motor drivers, servo outputs, capacitive touch inputs, a level-shifted NeoPixel driver, and a 3W I2S audio amplifier — all managed over I2C via the Adafru...

SKU: AF-1850

Add a touch of sparkle to your wearables with the Adafruit Gemma Sequin Starter Pack. This beginner-friendly kit includes a GEMMA V2 sewable microcontroller, warm white LED sequins, conductive thread, needles, and a coin cell battery holder — everything you need to start sewing glowing electronic...

SKU: AF-2716

The Adafruit SPW2430 Silicon MEMS Microphone Breakout is a compact, low-cost microphone module that detects sound and converts it to an analog voltage — no external bias resistor or amplifier needed. With a frequency range of 100 Hz to 10 kHz, it's well suited for general-purpose audio recording,...

SKU: AF-3317

The Adafruit VL53L0X is a Time-of-Flight (ToF) distance sensor from ST that uses an invisible laser to measure distances from approximately 50 mm to 1200 mm. By timing how long the laser light takes to bounce back, it delivers precise distance readings without the linearity issues or double-imagi...

SKU: AF-4565

The Adafruit LSM6DSOX + LIS3MDL FeatherWing is a precision 9 Degree of Freedom (9-DoF) IMU add-on for any Feather board. It combines the LSM6DSOX accelerometer/gyroscope — known for its exceptionally low gyro drift and noise — with the LIS3MDL magnetometer for complete orientation and heading sen...

SKU: AF-3127

The Adafruit 0.54" Quad Alphanumeric FeatherWing Display in white adds a bright, easy-to-read 4-character 14-segment LED display to any Feather microcontroller. Each character can show full alphanumeric text (A–Z, 0–9) plus symbols, making it ideal for clocks, sensor readouts, status messages, an...

SKU: AF-3251

The Adafruit Si7021 is a temperature and humidity sensor from Silicon Labs with a PTFE filter for protection against dust and contaminants. It provides ±3% relative humidity accuracy over 0–80% RH and ±0.4 °C temperature accuracy from −10 to +85 °C, all communicated over a simple I2C interface. ...

SKU: AF-2264

The Adafruit FT232H Breakout turns your computer into a versatile interface for hardware protocols. Using the FTDI FT232H chip with its multi-protocol synchronous serial engine, you can communicate directly with I2C, SPI, JTAG, and serial UART devices — plus read and write digital GPIO pins — all...

SKU: AF-3622

Add heat-vision to any Feather board with the Adafruit AMG8833 Thermal Camera FeatherWing. This sensor from Panasonic contains an 8×8 array of infrared thermal sensors that returns 64 individual temperature readings over I2C — like a compact thermal camera in FeatherWing form factor. The AMG8833...

SKU: AF-2948

The Adafruit LED Charlieplexed Matrix is a 9×16 grid of yellow LEDs arranged in a Charlieplexed configuration. Designed to pair with the IS31FL3731 LED matrix driver, this display lets you create scrolling text, animations, and visual effects with individually controllable LEDs. This is a bare L...

SKU: AF-1272

The Adafruit Ultimate GPS Logger Shield combines the popular Ultimate GPS module with a MicroSD card slot, giving your Arduino a complete GPS datalogging solution. Built around the MTK3339 chipset, it tracks up to 22 satellites on 66 channels with -165 dBm sensitivity and delivers up to 10 positi...

SKU: AF-5882 · MPN: ADA5882

The Adafruit DC Power BFF Add-On lets you power your QT Py or Xiao development board from a DC source up to 20V. The on-board MPM3610 integrated buck converter steps down the input to 5V at up to 1A, with no heat sink required — providing plenty of power for LEDs, WiFi, displays, and small motors...

SKU: AF-4464

The Adafruit ICM-20649 breakout features a wide-range 6-DoF IMU capable of measuring up to ±30g acceleration and ±4000°/s gyroscope rotation — roughly double the range of standard IMUs. When typical ±16g accelerometers and ±2000°/s gyros aren't enough, this sensor delivers the extended measuremen...

SKU: AF-5709

The Adafruit CAN Bus FeatherWing adds CAN bus networking to any Feather board. It uses the MCP2515 CAN controller and TJA1051/3 transceiver to send and receive messages in standard or extended format at up to 1 Mbps over a two-wire differential bus. Only an SPI port and two pins (chip-select and ...

SKU: AF-3654

Add WiFi connectivity to your Arduino-compatible board with the Adafruit WINC1500 WiFi Shield, featuring the FCC-certified ATWINC1500 module from Atmel. This 802.11b/g/n shield supports WEP, WPA, and WPA2 encryption with TLS 1.2 for secure connections, and communicates over SPI at speeds up to 12...

SKU: AF-3191

The Adafruit Power Relay FeatherWing lets you switch high-power loads — lamps, fans, solenoids, small appliances, and more — directly from any Feather microcontroller board. With a switching capacity of up to 10A at 120 VAC or 5A at 240 VAC (resistive loads), it can handle up to 1,200 watts. The...

SKU: AF-3653

Add WiFi connectivity to your Arduino-compatible board with the Adafruit WINC1500 WiFi Shield, featuring the FCC-certified ATWINC1500 module from Atmel. This 802.11b/g/n shield supports WEP, WPA, and WPA2 encryption with TLS 1.2 for secure connections, and communicates over SPI at speeds up to 12...

SKU: AF-4147

Add motion and precision temperature sensing to any Feather board with this all-in-one sensor FeatherWing from Adafruit. It combines two high-quality Analog Devices sensors — the ADXL343 triple-axis accelerometer and the ADT7410 precision temperature sensor — on a single FeatherWing PCB. Both se...

SKU: AF-3405

The Adafruit HUZZAH32 ESP32 Feather Board brings the powerful Espressif ESP32 dual-core processor into the Adafruit Feather form factor. With WiFi, Bluetooth Classic, and BLE support, a built-in USB-to-serial converter, automatic bootloader reset, and LiPo battery charging, it's a fully featured ...