All Products

SKU: SF-PRT-14219

A 2×AAA battery holder with a sliding cover and built-in ON/OFF switch. The cover keeps batteries secure, and the switch provides convenient power control for your project. Wire leads are approximately 150 mm long with 5 mm tinned ends. Specifications Capacity – 2× AAA batteries (3 V total) S...

SKU: AF-67

A 9V battery holder with a built-in on/off switch and a pre-attached 5.5mm/2.1mm centre-positive barrel plug. Ready to use out of the box — snap in a 9V battery, plug into your Arduino or other development board, and use the switch to control power. Key Features On/Off Switch – Conveniently co...

SKU: AF-5967 · MPN: ADA5967

The Adafruit Proto Tripler PiCowbell gives your Raspberry Pi Pico or Pico W three side-by-side socket slots — plug in your Pico and up to two PiCowbell accessories with no soldering or stacking headers required. It also includes LiPo battery charging, a power switch, reset button, STEMMA QT conne...

SKU: SF-PRT-18769

This 3xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover as well as an ON/OFF switch that can be used to control power to your project. The 6" (~150mm) cable has been terminated with a JST connector. Note: Please keep in...

SKU: EF-EF11085

A clear battery holder designed for the BBC micro:bit, holding two AAA batteries. Features a built-in on/off switch and a PH2.0 connector that plugs directly into the micro:bit's battery port. The transparent casing lets you see the batteries inside. Specifications Battery Type – 2× AAA (not i...

SKU: LB-BATTERYAA

A 2× AA battery holder with on/off switch, designed for powering the BBC micro:bit on the go. The JST connector plugs directly into the micro:bit's battery port, and the ~14 cm cable provides enough length for flexible mounting. Key Features 2× AA Battery Holder – Provides 3 V from standard AA...

SKU: AF-5906 · MPN: ADA5906

The Adafruit Proto Doubler PiCowbell gives your Raspberry Pi Pico or Pico W two side-by-side socket slots — plug in your Pico on one side and a PiCowbell accessory on the other, no soldering or stacking headers required. It also adds LiPo battery charging, a power switch, reset button, STEMMA QT ...

SKU: SF-PRT-15101

This is a unique two-cell AAA battery holder built specifically for the BBC micro:bit. The 6" (~150mm) cable has been terminated with a JST-PH connector. The connector mates the JST socket on the micro:bit perfectly, allowing you to easily make your project battery powered. Note: Please k...

SKU: LB-LS0821

This battery enclosure (with switch) for the BBC micro:bit is the perfect way to power your micro:bit on the go. Specifications:  2x AAA Battery Enclosure Cable Length: ~14cm JST Cable Connector (compatible with the BBC micro:bit power connector). Dimensions: 6.5cm x 2.8cm

SKU: LB-AAA-BATTERY

A small, but mighty power supply. This board was designed to be as small and inconspicuous as possible. Pop in a AAA battery, flip the power switch, and you will have a 5V supply to power your E-Textile circuit. Good up to 200mA. Short circuit protected. This board has AAA battery clips but ...

SKU: DF-DFR1216-1 · MPN: DFR1216-1

This multi-function expansion board adds power, I/O and drive capability to UNIHIKER M10/K10 and micro:bit projects. It is designed for mobile robots, portable interactive builds and maker projects that need more connectivity than the main controller can provide on its own.The board expands your ...

SKU: AF-6352 · MPN: ADA6352

This classroom-friendly kit pairs a micro:bit v2.2 with a simple soil sensor so students can monitor a pot plant and learn a bit of programming at the same time. It was designed to work with the "FarmBeats for Students" curriculum, where the micro:bit can show smile and frown status reports to in...

SKU: SF-PRT-09925

This 2xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small Phillips head screw. Another bonus is the ON/OFF switch which can be used to control power to your project. The leads are about 1...

SKU: PL-1155

A compact enclosed battery holder for six AA batteries, providing approximately 9V (alkaline) or 7.2V (NiMH rechargeable) from a series configuration. Features bare wire leads for flexible integration into your project. Key Features 6-Cell Capacity – Holds six AA batteries in series Enclosed ...

SKU: AF-4193

A slim 2×AA battery holder with a built-in on/off switch and genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and portable builds without needing to disconnect the battery to turn off power. The...

SKU: SF-KIT-27213 · MPN: KIT-27213

This kit brings together the main parts needed to evaluate and deploy a LoRaWAN® IoT sensor system: a Digi HX15 Gateway for LoRaWAN®, a SparkFun IoT Node for LoRaWAN® board and a SparkFun ENS160/BME280 Qwiic Environmental Combo Board.The IoT Node ships with firmware installed that automatically c...

SKU: AF-4422 · MPN: ADA4422

This 220 piece connector assortment gives your workstation a handy supply of 2.0mm pitch JST-PH compatible plugs, sockets and crimp terminals. It is a useful kit for prototyping, repairs and making up custom leads for common maker electronics.JST-PH style connectors are widely used in electronics...

SKU: PR-PIM610

A hackable, programmable badge with E Ink® display, powered by Raspberry Pi RP2040. In honour of Raspberry Pi's 10th birthday, we've fused a RP2040 microcontroller with an EPD display to make a stylishly monochrome, maker friendly, e-paper badge(r) to attach to your person, your office door...

SKU: AF-783

A compact coin cell battery holder designed for small portable and wearable electronics projects. It holds two 20mm coin cells (CR2032 is the most common size) wired in series to provide 6V nominal output, with an on/off switch built into the top for convenient power control. The holder features...

SKU: AF-1349

A really tiny portable inverter for EL wire. Powers off of a single AAA battery (not included!), it can drive up to 50cm / 20 inches of our high-brightness EL wire or 10cm x 1cm long piece of EL tape for 3 hours (or longer if the EL wire is less than 50cm long). There is a switch on the side f...