All Products

SKU: AF-2011

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 2000mAh. If you need a larger (or smaller!) battery, we have a full range of LiPoly batteriesThe batteries ...

SKU: SF-GPS-28870 · MPN: GPS-28870

Add precise positioning and orientation to a GNSS Flex carrier with this LG580P-based module. It is built for high-performance navigation, combining centimetre-level RTK positioning with real-time heading data for robotics, precision agriculture and autonomous vehicle projects.The module is part ...

SKU: PI-TEK002

A tiny, vibrating motor, easily attachable to paper or fabric! Just connect 3-5V across it, polarity doesn't matter, and it'll BUUUUZZZZZZ!!! The voltage (and hence current) supplied from LIR2032 rechargeable coin cell batteries may damage the Teknikio LED boards, so please ONLY...

SKU: SF-SEN-09088

This is a very small light sensor. A photocell changes (also called a photodetector, photo resistor, CdS or photoconductive cell) resistance depending on the amount of light it is exposed to. These little sensors make great ambient light triggers (when light in the room turns on, do something).Fe...

SKU: AF-2922

Add datalogging capability to any Feather board with the Adalogger FeatherWing. This add-on combines a battery-backed real-time clock (PCF8523) with a microSD card socket, giving your project accurate timestamps and local data storage in one compact wing. The RTC communicates over I2C with a 32 ...

SKU: AF-4282

The Adafruit PiRTC Precise DS3231 is a high-accuracy, battery-backed real-time clock that plugs directly onto your Raspberry Pi's GPIO header. Built around a genuine Maxim DS3231 with an integrated temperature-compensated crystal oscillator (TCXO), it delivers exceptional timekeeping accuracy — f...

SKU: AF-1867

A breakout board with a CR1220 coin cell battery holder, an on/off switch, and 0.1″ pitch breakout pins. Ideal for powering very low-current projects or providing switchable battery backup for a real-time clock (RTC) module. The board breaks out four pins: two ground pins, one switched power pin...

SKU: DF-DFR1195 · MPN: DFR1195

This ESP32-S3 development board is built for long-range IoT prototyping using LoRa, LoRaWAN and Meshtastic. It can be used for one-to-one LoRa links, one-to-many LoRa communication, standard LoRaWAN networks, or Meshtastic mesh networking.The board is designed to be approachable for makers and de...

SKU: AF-67

A 9V battery holder with a built-in on/off switch and a pre-attached 5.5mm/2.1mm centre-positive barrel plug. Ready to use out of the box — snap in a 9V battery, plug into your Arduino or other development board, and use the switch to control power. Key Features On/Off Switch – Conveniently co...

SKU: AF-3028

A Feather board without ambition is a Feather board without FeatherWings! This is the DS3231 Precision RTC FeatherWing: it adds an extremely accurate I2C-integrated Real Time Clock (RTC) with a Temperature Compensated Crystal Oscillator (TCXO)  to any Feather main board. This RTC is the m...

SKU: AF-1082

Click click click - oh pardon me I was having fun clicking away on my mechanical decade counters. Each order comes with five individual counters. They're snap together so you can connect as many or as few as you'd like. Each one has two buttons - an up counter and down counter. Once you get to 9 ...

SKU: LB-LS3337

An enclosed battery holder for three AAA cells with a built-in on/off switch. The snap-on lid fully covers the batteries, keeping them secure during use. Wire leads allow you to connect directly to your project. Three AAA cells in series provide approximately 4.5V (alkaline) or 3.6V (NiMH), suit...