All Products

SKU: PH-103393

A Raspberry Pi motor controller HAT built around the L293D dual H-bridge driver IC, designed to make building a Raspberry Pi robot easy and fun. Control up to 4 DC motors or 2 stepper motors at up to 600 mA (1 A peak) per channel. The board includes breakout connectors for IR line sensors and an...

SKU: AF-2348

The Adafruit DC & Stepper Motor HAT drives up to 4 DC motors or 2 stepper motors from your Raspberry Pi, with full PWM speed control. It uses a dedicated PWM driver chip over I2C, so only two pins (SDA/SCL) are needed — leaving the rest free for other I2C devices or HATs. The TB6612 MOSFET motor...

SKU: PL-5033

The Motoron M3H256 Triple Motor Controller makes it easy to control DC motors from a Raspberry Pi (Model B+ or newer) through an I²C interface. Each module can independently control up to three motors, and multiple Motoron boards can be stacked on top of the same Raspberry Pi for projects that ne...

SKU: AF-6109 · MPN: ADA6109

The Adafruit A4988 Stepper Motor Driver Breakout simplifies stepper motor control down to just two pins — a direction pin and a step pin. Each pulse on the step pin advances the motor by one step or microstep, making it straightforward to achieve precise, controlled motion without complex timer o...

SKU: WS-22311

HRB8825 Stepper Motor HAT For Raspberry Pi, Drives Two Stepper Motors, Up To 1/32 Microstepping Stepper Motor HAT (B) Alternative Solution Of Stepper Motor HAT, Drives Two Stepper Motors, Up To 1/32 Microstepping For 3D Printer, Sculpturing machine, Mechanical arm... Features At A ...

SKU: EC-ARS27361T

This motor shield uses dual TB6612 MOSFET drivers and a PCA9685PW I2C PWM controller to drive up to 4 DC motors or 2 stepper motors from an Arduino or compatible board. All motor control and speed management is handled via the I2C bus, freeing up digital pins for other uses. The stackable design...

SKU: AF-4280

The Adafruit DC & Stepper Motor Bonnet drives up to 4 DC motors or 2 stepper motors from your Raspberry Pi, with full PWM speed control. It uses a dedicated PWM driver chip over I2C, so only two pins (SDA/SCL) are needed — leaving the rest free for other I2C devices or HATs. The TB6612 MOSFET mo...

SKU: AF-6353 · MPN: ADA6353

The Adafruit STSPIN220 Stepper Motor Driver Breakout makes controlling bipolar stepper motors simple with a GPIO-only interface — just two pins (DIR and STEP) are all you need. It defaults to 1/16 microstepping and supports up to 1/256 microstepping via mode pin configuration, making it ideal for...

SKU: AF-6121 · MPN: ADA6121

The Adafruit TMC2209 Stepper Motor Driver Breakout Board makes controlling stepper motors easy and virtually silent. Using Trinamic's "Stealth Chopper" technology, this driver delivers smooth, quiet microstepping with just two control pins — no timers, PWM, or real-time microcontroller required. ...

SKU: SF-ROB-30118 · MPN: ROB-30118

Stepper motor builds often need a microcontroller, a separate driver, a 12V or 24V supply and plenty of wiring. This compact controller from Things by Josh brings that stack together in one unit designed to mount directly to the back of a standard NEMA 17 stepper motor.Power comes in via USB-C Po...

SKU: AF-807

Run four solenoids, two DC motors or one bi-polar or uni-polar stepper with up to 600mA per channel using the L293D. These are perhaps better known as "the drivers in our Adafruit Motorshield". If you accidentally damaged the drivers in a shield, you can use one of these puppies to replace it....

SKU: AF-3297

The Adafruit DRV8833 is a dual H-bridge motor driver breakout, capable of driving two DC motors bidirectionally or one bipolar/unipolar stepper motor at up to 1.2 A per channel. It's well suited for low-voltage applications, operating from 2.7V to 10.8V motor power. The DRV8833 features built-in...

SKU: DF-DFR0592

The DC Motor Driver HAT is a Raspberry Pi add-on board that drives up to two DC motors via I2C. Built around the TB6612FNG motor driver chip with 1.2 A continuous current per channel (2 A peak), it supports both standard DC motors and motors with encoders through the on-board encoder interface. ...

SKU: DF-DRI0054 · MPN: DRI0054

##Introduction The multifunctional motor driver expansion board is designed for Raspberry Pi Zero/Zero W/A+/B+/2B/3B/3B+/4B. This fully-featured robot motor expansion board is capable of supporting multiple motors, stepper motors, and servos simultaneously. It also provides spare camera and DIP d...

SKU: AF-858

This is a great first stepper motor, good for small projects and experimenting with steppers. This uni-polar motor has a built in mounting plate with two mounting holes. There are only 32 step (11.25 degree) per revolution, and inside is a 1/16 reduction gear set. (Actually its 1/16.032 but for m...

SKU: DF-DFR0513

This motor driver module is a special PPM signal motor controller for Aero modelling remote control. It is designed by DFRobot and it can be controlled by RC transmitter. The driver can convert PPM signal to the motor speed and direction control signal. There are two signal receiving chan...

SKU: AF-2927

A Feather board without ambition is a Feather board without FeatherWings! This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 stepper and 2 DC motors). Using our Feather Stacking Headers or Feather Fem...

SKU: AF-1438

The Adafruit Motor/Stepper/Servo Shield v2.3 is the upgraded successor to the original Motor Shield, delivering higher current, lower voltage drop, and a fully I2C-based design that frees up your Arduino's PWM pins. Drive up to 4 DC motors or 2 stepper motors plus 2 hobby servos from a single sta...

SKU: DF-FIT1036 · MPN: FIT1036

This compact 4015 BLDC motor combines a high-torque outer rotor motor with a factory-integrated AS5600 magnetic encoder, making it a neat motion-control package for robotics and precision motion projects.It is designed for Field-Oriented Control (FOC), also known as vector control, to support smo...

SKU: AF-1750

The Synthetos gShield (formerly grblShield) V5 is a 3-axis CNC stepper motor driver shield for Arduino. Designed as a complete hardware companion for the grbl CNC motion control firmware, it turns an Arduino Uno into a capable CNC controller for mills, routers, laser cutters, and other motion-con...