All Products

SKU: AF-4979

The NeoKey FeatherWing adds two mechanical key switch sockets with individually addressable NeoPixel backlighting to any Feather-format microcontroller. Each socket accepts Cherry MX or compatible switches (Kailh, Gateron, etc.) without soldering, using Kailh hot-swap sockets. A reverse-mount Ne...

SKU: AF-4352

Build a handheld light-up button controller with this complete kit that pairs the Adafruit 4×4 NeoTrellis RGB Driver with a Feather M4 Express inside an elegant laser-cut acrylic enclosure. The 16 silicone buttons each have individually addressable NeoPixels underneath, and the seesaw I2C chip ha...

SKU: AF-4253

The Adafruit Quad 2×2 FeatherWing Kit lets you connect one Feather board to three FeatherWings simultaneously in a compact 2×2 grid layout — no stacking headers needed. All four sets of Feather pins are cross-connected, so every FeatherWing shares the same bus signals, power, and ground. Each of...

SKU: AF-2945

The NeoPixel FeatherWing adds a 4×8 matrix of 32 individually addressable RGB LEDs to any Adafruit Feather board. Using Feather stacking headers or female headers, the wing connects directly on top or bottom of your Feather for a compact, colourful display. Only one pin is required to control al...

SKU: AF-6054 · MPN: ADA6054

The Feather Mount for LEGO-Compatible Brick Systems lets you securely attach any standard-sized Feather or FeatherWing board (2" × 0.9" / 51 mm × 23 mm) to LEGO-compatible brick plates. No hot glue, epoxy, or tape needed — the mount snaps directly onto brick baseplates for a clean, secure build. ...

SKU: AF-4339

This laser-cut acrylic enclosure kit turns your 4×4 NeoTrellis setup into a handheld device with an elegant black and white design and beautifully diffused button illumination. Designed to house any Adafruit Feather board (except FONA) alongside the NeoTrellis RGB Driver PCB. The enclosure inclu...

SKU: AF-3173

A simple, solder-on terminal block set sized to fit Adafruit Feather boards and FeatherWings. These 0.1″ pitch terminal blocks let you make secure, screw-down wire connections without soldering wires directly to your board — making projects easier to build, maintain, and modify. Compatible with ...

SKU: AF-5679

The Adafruit Floppy FeatherWing lets you read and write 3.5-inch or 5.25-inch floppy disks using a Feather microcontroller. It connects to standard 34-pin IDC floppy drives and includes built-in level shifting between 3.3 V Feather logic and the 5 V signals that floppy drives require. Floppy dri...

SKU: AF-4702

The Adafruit RGB Matrix FeatherWing Kit for nRF52840 lets you drive HUB75-type RGB LED matrices from nRF52840-based Feather boards. With built-in power regulation and a compact form factor, it's the easiest way to create colourful scrolling displays and LED wall projects using the Feather ecosyst...

SKU: AF-4147

Add motion and precision temperature sensing to any Feather board with this all-in-one sensor FeatherWing from Adafruit. It combines two high-quality Analog Devices sensors — the ADXL343 triple-axis accelerometer and the ADT7410 precision temperature sensor — on a single FeatherWing PCB. Both se...

SKU: AF-4372

This laser-cut acrylic enclosure kit turns your 8×8 NeoTrellis setup (four 4×4 NeoTrellis boards) into a handheld device with an elegant black and white design and beautifully diffused button illumination. Designed to house any Adafruit Feather board (except FONA) alongside four NeoTrellis RGB Dr...

SKU: AF-6305 · MPN: ADA6305

Keep your Adafruit Feather RP2350 with HSTX Port protected during use and transport with this cute, minimal enclosure. It has been custom-designed to fit the Feather RP2350 HSTX board, including the version with 8MB of PSRAM.The case is 3D printed from translucent milky white plastic using an SLA...

SKU: AF-2890

This is the FeatherWing Doubler - a prototyping add-on and more for all Feather boards. This is similar to our FeatherWing Proto except there are two! The magic of the Doubler comes when stacking a Feather and another board on top of the Doubler so you can work with both boards si...

SKU: AF-3136

The Adafruit 15×7 CharliePlex LED Matrix FeatherWing in Green adds a bright, compact 105-LED grid to any Feather board. The onboard IS31FL3731 driver handles all the charlieplexing over I2C, with 8-bit (256-level) PWM dimming on every individual LED — no complex wiring needed. The driver chip in...

SKU: AF-6241 · MPN: ADA6241

A custom-designed snap-on enclosure for the Adafruit Feather RP2040 with DVI Output Port. 3D printed using an SLA process in translucent milky white plastic, it provides a clean, protective case with no visible layer lines or surface imperfections. No screws or glue required — simply snap the Fe...

SKU: AF-3315

A 2.4" TFT touchscreen display shield for the Adafruit Feather ecosystem. Featuring a 320×240 pixel display with 16-bit colour, a resistive touchscreen, and a built-in microSD card slot, this FeatherWing adds a full interactive display to any Feather board via SPI. Comes fully assembled with dua...

SKU: AF-3036

The Adafruit RGB Matrix FeatherWing Kit lets you drive HUB75-type RGB LED matrices from any SAMD21 M0 or SAMD51 M4 Feather board. With built-in power regulation and a compact form factor, it's the easiest way to create colourful scrolling displays and LED wall projects using the Feather ecosystem...

SKU: AF-3108

Add a bright, easy-to-read numeric display to your Feather project with the Adafruit 4-Digit 7-Segment FeatherWing in red. This combo pack includes the HT16K33-based FeatherWing backpack and a matching 0.56" tall red 7-segment display with decimal points and a centre colon for clock displays. Th...

SKU: AF-2940

These two Short Female Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business! These headers are particularly cute and tiny with a body height of just 5.0 mm they are the best way to minimize the amount of space your Feather ...

SKU: AF-2900

A Feather board without ambition is a Feather board without FeatherWings! This is the FeatherWing OLED: it adds a 128x32 monochrome OLED plus 3 user buttons to any Feather main board. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top of your Feat...