All Products
Showing 1-20 of 60 products
Waterproof 3xAA Battery Holder with On/Off Switch
Keep your power source safe and toasty in these waterproof 3xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the case (its black and hard to see in the photos but it is there) and attaches togeth...
3 x AA Battery Holder with On/Off Switch, JST, and Belt Clip
A compact 3×AA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making it an ideal non-rechargeable alternative for 3.3V projects that use a JST batte...
3-AA Battery Holder, Enclosed with Switch
An enclosed battery holder for three AA cells with a built-in on/off switch. The snap-on lid slides over the batteries to fully enclose them, keeping the cells secure during use. Provides approximately 4.5 V with three alkaline AA batteries (3 × 1.5 V) or 3.6 V with three NiMH rechargeable cells...
3xAA Battery Holder
This enclosed battery holder takes 3× AA batteries in series, providing approximately 4.5V from alkaline cells or 3.6V from NiMH/NiCd rechargeables. It features a built-in on/off switch and a sliding, removable cover for easy battery access. Compatible with both non-rechargeable alkaline and rec...
Battery Holder 3xAA with Cover and Switch - JST Connector
This 3xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover as well as an ON/OFF switch that can be used to control power to your project. The 6" (~150mm) cable has been terminated with a JST connector. Note: Please keep in...
Battery Holder 3xAA with Cover and Switch
This 3xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small phillips head screw. Another bonus is the ON/OFF switch which can be used to control power to your project.The leads are about 150mm...
4 x AA Battery Holder with 2.1mm Plug and On/Off Switch
A 4×AA battery holder with a built-in on/off switch and a 13cm (5″) power cable terminating in a centre-positive 2.1mm DC barrel jack. Provides convenient portable power with easy switching for development boards and projects that accept a standard DC barrel jack input. Delivers approximately 4....
8 x AA battery holder with 5.5mm/2.1mm Plug and On/Off Switch
This 8×AA battery holder provides a portable power source with a built-in on/off switch and a standard 5.5 mm / 2.1 mm DC barrel plug for easy connection to Arduino boards, LED strips, motors, and other 12V devices. Use alkaline AAs for approximately 12V at 3000–4000 mAh, or rechargeable NiMH cel...
Kitronik ZIP Halo HD for micro:bit
The Kitronik ZIP Halo HD for micro:bit is the ultimate micro:bit interface. 60 full-colour ZIP LEDs, Pins 1 & 2 broken out, MEMs mic, Piezo sounder, RTC & more!The Kitronik Halo HD board for the BBC micro:bit incorporates 60 individually addressable full colour ZIP LEDs. It also breaks out P1 and...
Lilypad Battery Holder with Switch - 10 PACK
A sewable coin cell battery holder with built-in on/off slide switch, designed for e-textile and wearable electronics projects. This bulk 10-pack is ideal for classrooms, workshops, and makerspaces. Each holder accepts a standard 20 mm coin cell battery (CR2032) and features sewable tabs for eas...
12mm Coin Cell Breakout w/ On-Off Switch
A breakout board with a CR1220 coin cell battery holder, an on/off switch, and 0.1″ pitch breakout pins. Ideal for powering very low-current projects or providing switchable battery backup for a real-time clock (RTC) module. The board breaks out four pins: two ground pins, one switched power pin...
2 x AA Battery Holder with On/Off Switch JST PH Connector
A slim 2×AA battery holder with a built-in on/off switch and genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and portable builds without needing to disconnect the battery to turn off power. The...
Waterproof 2xAA Battery Holder with On/Off Switch
Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the case (its black and hard to see in the photos but it is there) and attaches togeth...
Adafruit LED Glasses Starter Kit
The Adafruit LED Glasses Starter Kit includes everything you need to build a complete pair of programmable LED glasses. Pair the 116-LED front panel with the Bluetooth-enabled nRF52840 driver board, snap them onto the included fashion frames, and you're ready to create dazzling wearable light dis...
MicroUSB Battery Holder (3xAA)
This battery holder takes three AA cells and provides a simple way to power compatible Arduino-style boards via a Micro USB connection.Use it with NiMH or NiCd rechargeable cells for a 3.6V battery pack, or with alkaline cells for a 4.5V battery pack. The holder is made from plastic and includes ...
Kitronik Air Quality and Environmental Board for micro:bit
The Kitronik Air Quality Board provides a complete air monitoring and reporting solution for the BBC micro:bit. The wealth of onboard sensors and connection points allow you to collect extensive air quality data that can be stored in onboard memory and displayed on the OLED screen or transferred ...
4x AA Battery Holder (with Power Switch, DC2.1 Jack, and Cover)
A compact 4×AA battery holder with a built-in on/off power switch, DC2.1 barrel jack output, and a protective cover. Ideal for powering Arduino, Raspberry Pi, and other microcontroller projects with a portable 6V supply. The holder accepts four standard AA batteries (1.2V rechargeable or 1.5V al...
Micro:bit AA battery holder with Switch
A 2× AA battery holder with on/off switch, designed for powering the BBC micro:bit on the go. The JST connector plugs directly into the micro:bit's battery port, and the ~14 cm cable provides enough length for flexible mounting. Key Features 2× AA Battery Holder – Provides 3 V from standard AA...
DFRobot Building Block Expansion Board Bundle for UNIHIKER M10
·
This bundle adds motor, servo and sensor expansion to the UNIHIKER M10 single-board computer, using the included Type-C to HY2.0-4P communication cable to bridge the M10 to the expansion board.The board includes an integrated 18650 battery holder so your controller, motors and sensors can run fro...
Kitronik ARCADE Max for Makecode Arcade
Develop your coding skills with the ARCADE Max, a fully featured programmable gamepad for use with the MakeCode Arcade block editor, featuring a large 2.4" screen and familiar design shape.The Kitronik ARCADE Max for Makecode Arcade is an all-in-one handheld gaming platform, that can help you lea...
