All Products

SKU: LB-EAGLED-LED-Y

EagLED yellow sewable LEDs designed for e-textiles and wearable electronics. These Australian-made LEDs come attached in a strip — simply snap them apart and sew into clothing, accessories, or fabric projects using conductive thread. A lower-cost alternative to LilyPad LEDs. Each LED lights up w...

SKU: LB-ETEXTILELED-YG

A single yellow-green LED module designed for e-textiles projects. Each unit features sewable tabs so it can be stitched directly into fabric using conductive thread. The thicker PCB design makes it more durable than standard sewable LEDs. Compatible with a range of e-textiles input, output, pow...

SKU: LB-00211

The E-Textiles Rainbow LED strip contains seven LilyPad-style sewable LEDs in six colours, connected in a snap-apart strip. Break off individual LEDs as needed and sew them into clothing, accessories, or craft projects using conductive thread. Each LED board has its colour printed on the back fo...

SKU: LB-EAGLED-LED-O

EagLED LEDs are purpose-built for e-textiles and wearable projects. This pack of 10 orange sewable LEDs come attached to each other on a snappable strip — simply break them apart as needed and sew them into clothing, accessories, or whatever you can dream up. Made in Australia, they're a cost-eff...

SKU: LB-LR0309-45

A 1-metre length of soft conductive sewing thread made from stainless steel, designed for wearable electronics projects. Use it to sew electrical connections between LilyPad components, sewable LEDs, and batteries — replacing traditional wires with flexible, stitchable conductors. Key Features ...

SKU: KI-2762

Add an individually addressable full colour LED to your E-Textiles projects with the Kitronik Sewable ZIP LED. This new addition to our Electro Fashion range incorporates a full colour addressable ZIP LED, which can be controlled by a suitable processor such as the micro:bit. The four connecti...

SKU: KI-2715

A starter kit for e-textiles and wearable electronics from Kitronik's Electro-Fashion range. This Discovery Pack includes a curated selection of sewable components — LEDs, switches, coin cell holders, conductive thread, and batteries — everything you need to begin adding electronics to fabric pro...

SKU: LB-EAGLED-LED-G

EagLED LEDs were made for e-textiles! This is a simple pack of green wearable leds that are still attached to one another. Simply snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up! It is made in Australia and is a lower cost e-textiles led alternativ...

SKU: KI-2751

This wearable module is ideal for all of your e-textiles project needs including adding the endless possibilities of programming to your wearable projects!Video:Please note: other Kitronik products are included in this video. This PICAXE wearable module offers an easy introduction to the wor...

SKU: SF-KIT-13927

The LilyPad Sewable Electronics Kit is an introduction to the world of e-textiles and electronic sewing. Through a series of guided projects, you'll learn to sew basic circuits, light up LEDs, control them with buttons and switches, and experiment with a pre-programmed LilyMini circuit that react...

SKU: KI-2709

This sewable two position miniature slide switch from Kitronik allows LEDs to be turned on or off in your e-textiles projects.It has two connection points to which the conductive thread is connected. The PCBs are double sided making the conductive thread connection very reliable (see example pict...

SKU: LB-ETEXTILELED-W

A sewable white LED module designed for e-textile projects. This single-unit LED can be stitched directly into fabric using conductive thread, making it easy to add illumination to wearable electronics and textile-based circuits. The module uses a thicker PCB than typical LilyPad-style LEDs, pro...

SKU: KI-2746

When using through hole LEDs it can be hard to form the eyelets and then work out which leg is positive and negative. That's where these Sewable LED Holders come in! The 5mm LED holder boards, quickly and easily take any through hole 5mm LED and (after soldering in place) make them easy to use in...

SKU: LB-00110

If you are just getting started in sewable and wearable tech this is a great beginners project. It includes everything you need to make you own RAINBOW bookmark, hat, tie or anything else you can get a needle through.We have some great new LEDs that have a black PCB which works really well to hid...

SKU: PR-PIM316

An adorable acorn-shaped motion sensor designed to work with Bearables wearable LED badges. When you move or tilt the acorn, the connected badge's LEDs light up — bringing your wearable creation to life with simple, delightful interactivity. Part of the woodland-themed Bearables range, this sens...

SKU: SF-DEV-14631

This is the LilyPad USB Plus, a sewable electronics microcontroller board controlled by an ATmega32U4 with the Arduino bootloader. It has a built in power supply JST (and recharge circuit) and an on/off switch with the only extra piece of hardware you need to program the LilyPad USB Plus being a...

SKU: LB-EAGLED-LED-W

The EagLED is a sewable white LED designed and made in Sydney. Each pack contains 10 LEDs connected in a snap-apart strip, so you can break them off as needed for your project. Large sew tabs allow you to loop conductive thread through multiple times for a secure connection to fabric. The thin P...

SKU: SF-DEV-14346

The LilyPad ProtoSnap Plus is a sewable electronics prototyping board that you can use to explore circuits and programming, then break apart to make an interactive fabric or wearable project. Programming the ProtoSnap Plus is easy with the free Arduino software you’ll need to program the ATmega32...

SKU: DF-FIT0747 · MPN: FIT0747

This smooth stainless steel fibre conductive sewing thread is handy for soft circuits, wearables and e-textile projects where you need to stitch an electrical connection into fabric.Each roll provides 5m of thread with about 7Ω resistance per metre and a 0.5mm diameter. It can be used for touchsc...