All Products

SKU: AF-4193 · MPN: 4193

A slim 2×AA battery holder with a built-in on/off switch and genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and portable builds without needing to disconnect the battery to turn off power. The...

SKU: EF-EF10095

A 2×AA battery holder designed specifically for the BBC micro:bit. The built-in JST PH connector plugs directly into the micro:bit's battery socket, and the integrated on/off switch with a secure cover provides safe, convenient power control. Key Features micro:bit Compatible – JST PH connecto...

SKU: AF-4194 · MPN: 4194

A slim, open-top 2×AA battery holder with a genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, Adafruit boards, and microcontrollers with JST PH battery inputs. The JST PH connector polarity matches Adafruit's Li-I...

SKU: SF-PRT-14299

This is a unique two-cell AA battery holder built specifically for the BBC micro:bit. The 6" (~150mm) cable has been terminated with a JST-PH connector. The connector mates the JST socket on the micro:bit perfectly, allowing you to easily make your project battery powered.

SKU: LB-BATTERYAA

A 2× AA battery holder with on/off switch, designed for powering the BBC micro:bit on the go. The JST connector plugs directly into the micro:bit's battery port, and the ~14 cm cable provides enough length for flexible mounting. Key Features 2× AA Battery Holder – Provides 3 V from standard AA...

SKU: SF-PRT-09925

This 2xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small Phillips head screw. Another bonus is the ON/OFF switch which can be used to control power to your project. The leads are about 1...

SKU: EF-EF10111

A crystal-clear acrylic enclosure for the BBC micro:bit with an integrated 2×AA battery holder on the back. The two-piece case wraps the micro:bit while leaving the A and B buttons and edge connector gold fingers fully exposed for easy access. Key Features Material – Crystal acrylic, two-piece...

SKU: AF-783 · MPN: 783

A compact coin cell battery holder designed for small portable and wearable electronics projects. It holds two 20mm coin cells (CR2032 is the most common size) wired in series to provide 6V nominal output, with an on/off switch built into the top for convenient power control. The holder features...

SKU: SF-PRT-15101

This two-cell AAA battery holder is made for powering BBC micro:bit projects without needing to stay tethered to USB.The attached 6" (~150mm) lead is terminated with a JST-PH connector that mates with the JST socket on the micro:bit, making it simple to add portable power to your build.Note: JST ...

SKU: SF-PRT-09547

A 2×AA battery holder with a sliding cover secured by a Phillips head screw and a built-in ON/OFF switch for convenient power control. The 150mm tinned leads make it easy to solder into your projects. Key Features 2×AA Capacity – Provides 3V with alkaline batteries ON/OFF Switch – Built-in po...

SKU: LB-00253

A compact 3.7 V lithium-ion polymer (LiPo) battery with a 180 mAh capacity (~0.6 Wh). Thin, lightweight, and fitted with a genuine 2-pin JST-PH connector for reliable, snag-free connections to compatible chargers and development boards. Includes built-in protection circuitry to guard against ove...

SKU: AF-3287 · MPN: 3287

A compact 3×AA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making it an ideal non-rechargeable alternative for 3.3V projects that use a JST batte...

SKU: AF-770 · MPN: 770

Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the case (its black and hard to see in the photos but it is there) and attaches togeth...

SKU: EDU-MBCP-30 · MPN: EDU-MBCP-30

Everything a teacher needs for a one-micro:bit-per-student classroom: 30× BBC micro:bit v2 boards, 30× colour-coded USB cables, 30× AAA battery holders, and 30× protective cases — ready to hand out, plug in, and code. Ideal for primary and secondary Digital Technologies, Design & Technologies, a...

SKU: LB-MICROCLASS

DescriptionThe micro:bit Classroom Lab Pack includes 10 micro:bit boards and everything you need to get you started with the new learning platform. The Lab Pack has everything you need, including micro:bits, cables, battery packs and a few parts to experiment with. This package provides an easy w...

SKU: SF-PRT-13855

A slim, lightweight 3.7V 2000 mAh lithium-ion battery terminated with a standard 2-pin JST-PH connector (2 mm pin spacing). Built-in protection circuitry guards against overvoltage, overcurrent, and undervoltage conditions. Key Features Capacity – 2000 mAh at 3.7V nominal Connector – 2-pin JS...

SKU: AF-1131 · MPN: 1131

A 500 mm extension cable with a JST-PH 2-pin socket on one end and a matching plug on the other. The colour-coded wires make it easy to verify correct polarity. Compatible with JST-PH terminated battery packs including LiPo, Li-Ion, and AAA battery holders. Key Features JST-PH 2-Pin Connectors...

SKU: AF-6391 · MPN: ADA6391

This small accessibility tool helps remove LiPoly and LiIon batteries with JST connectors from a board without tugging on the battery wires.The 3D-printed puller slips over the JST PH connector so you can line it up with the socket and gently lift it out. It is handy for anyone who finds tiny bat...

SKU: AF-5627

A curated electronics kit built around the Adafruit CLUE board and PyLeap — Adafruit's app for wirelessly transferring code and assets from the Learn system directly to your device. No complicated setup or USB cable needed for programming once you're connected via Bluetooth. The CLUE board packs...

SKU: DF-DFR1216-1 · MPN: DFR1216-1

This multi-function expansion board adds power, I/O and drive capability to UNIHIKER M10/K10 and micro:bit projects. It is designed for mobile robots, portable interactive builds and maker projects that need more connectivity than the main controller can provide on its own.The board expands your ...