All Products
Showing 1-20 of 60 products
Lilypad Battery Holder with Switch - 10 PACK
A sewable coin cell battery holder with built-in on/off slide switch, designed for e-textile and wearable electronics projects. This bulk 10-pack is ideal for classrooms, workshops, and makerspaces. Each holder accepts a standard 20 mm coin cell battery (CR2032) and features sewable tabs for eas...
3 x AA Battery Holder with On/Off Switch, JST, and Belt Clip
·
A compact 3×AA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making it an ideal non-rechargeable alternative for 3.3V projects that use a JST batte...
3-AA Battery Holder, Enclosed with Switch
An enclosed battery holder for three AA cells with a built-in on/off switch. The snap-on lid slides over the batteries to fully enclose them, keeping the cells secure during use. Provides approximately 4.5 V with three alkaline AA batteries (3 × 1.5 V) or 3.6 V with three NiMH rechargeable cells...
8 x AA battery holder with 5.5mm/2.1mm Plug and On/Off Switch
·
This 8×AA battery holder provides a portable power source with a built-in on/off switch and a standard 5.5 mm / 2.1 mm DC barrel plug for easy connection to Arduino boards, LED strips, motors, and other 12V devices. Use alkaline AAs for approximately 12V at 3000–4000 mAh, or rechargeable NiMH cel...
4x AA Battery Holder (with Power Switch, DC2.1 Jack, and Cover)
A compact 4×AA battery holder with a built-in on/off power switch, DC2.1 barrel jack output, and a protective cover. Ideal for powering Arduino, Raspberry Pi, and other microcontroller projects with a portable 6V supply. The holder accepts four standard AA batteries (1.2V rechargeable or 1.5V al...
9V battery holder with switch 5.5mm/2.1mm plug
·
A 9V battery holder with a built-in on/off switch and a pre-attached 5.5mm/2.1mm centre-positive barrel plug. Ready to use out of the box — snap in a 9V battery, plug into your Arduino or other development board, and use the switch to control power. Key Features On/Off Switch – Conveniently co...
3 x AAA Battery Holder with On/Off Switch, JST, and Belt Clip
·
A slim 3×AAA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making it an ideal non-rechargeable alternative for 3.3V projects that use a JST battery...
4 x AA Battery Holder with 2.1mm Plug and On/Off Switch
·
A 4×AA battery holder with a built-in on/off switch and a 13cm (5″) power cable terminating in a centre-positive 2.1mm DC barrel jack. Provides convenient portable power with easy switching for development boards and projects that accept a standard DC barrel jack input. Delivers approximately 4....
Battery Holder - 2xAAA with Cover and Switch
A 2×AAA battery holder with a sliding cover and built-in ON/OFF switch. The cover keeps batteries secure, and the switch provides convenient power control for your project. Wire leads are approximately 150 mm long with 5 mm tinned ends. Specifications Capacity – 2× AAA batteries (3 V total) S...
Battery Holder with Switch - 2 x AA
Add a tidy power source to your battery-powered project with this holder for two AA cells. It provides around 3V from 2 x 1.5V batteries, making it suitable for many small electronics builds.The holder has a removable sliding cover secured with a small Phillips head screw, helping keep the cells ...
2 x AA Battery Holder with On/Off Switch JST PH Connector
·
A slim 2×AA battery holder with a built-in on/off switch and genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and portable builds without needing to disconnect the battery to turn off power. The...
3 x AAA Battery Holder with Switch
An enclosed battery holder for three AAA cells with a built-in on/off switch. The snap-on lid fully covers the batteries, keeping them secure during use. Wire leads allow you to connect directly to your project. Three AAA cells in series provide approximately 4.5V (alkaline) or 3.6V (NiMH), suit...
4 x AA Battery Holder with On/Off Switch
·
A 4×AA battery holder with a snap-on cover and built-in on/off switch. Holds four AA batteries in series, outputting a nominal 6V (alkaline) or 4.8V (NiMH), making it a convenient portable power source for 5V microcontroller projects. With alkaline batteries, you may want to add a 1N4001 diode i...
_1220x813.jpg.webp)
2xAAA Battery Holder with Cover and Power Switch
·
This compact battery holder is a handy portable power pack for small electronics and maker projects. It holds two AAA batteries and connects them in series, making it suitable for projects that need a simple removable battery supply.The holder includes a cover and an integrated power switch, so y...
3 x AAA Battery Holder with On/Off Switch and 2-Pin JST
·
A slim 3×AAA battery holder with a built-in on/off switch and JST 2-pin connector. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making it an ideal non-rechargeable alternative for 3.3V projects that use a JST battery connector. Uses a genui...
Coin Cell Battery Holder - Switched for Lilypad - 20mm
Sure, your flashing, chip-tune playing T-shirt is really cool at the party… but at some point you need to turn it off. And yes, you could just pull the battery, or maybe you’ve even sewn a LilyPad slide switch in-line. Wouldn’t it be nice if there was just a switch on the battery? Well, look no f...
2 x AAA Battery Holder with switch
A compact 2×AAA battery holder with a built-in power switch and JST connector, compatible with micro:bit and other boards that accept JST battery inputs. This is the same battery holder included in our micro:bit accessories kit. Key Features Power Switch – On/off switch for convenient power co...
9V Battery Holder
A snap-in 9V battery holder with a 5.5mm/2.1mm centre-positive barrel jack connector. The battery clicks securely into place, and three mounting holes allow you to attach the holder to an enclosure or chassis. Key Features Snap-In Design – Battery clicks securely into place 5.5mm/2.1mm Barrel...
2 x AA Battery Holder with Knife Switch
·
A 2×AA battery holder with a built-in knife switch for controlling power. Unlike typical slide switches, the knife switch provides a clear visual indicator of open and closed circuit states — making it an excellent tool for teaching basic electronics and circuit concepts. The holder takes two AA...
LilyPad Simple Power
The LilyPad Simple Power is a simple e-textile board that lets you connect and charge a lipo battery and switch it on or off, that’s it! We provide you with a JST connector and a slide switch, you supply the battery and sewing skills! With this LilyPad Simple Power, you should find no trouble in ...
