All Products
Showing 1-20 of 43 products
JST-PH Battery Extension Cable - 500mm
·
A 500 mm extension cable with a JST-PH 2-pin socket on one end and a matching plug on the other. The colour-coded wires make it easy to verify correct polarity. Compatible with JST-PH terminated battery packs including LiPo, Li-Ion, and AAA battery holders. Key Features JST-PH 2-Pin Connectors...
Adafruit LC709203F LiPoly / LiIon Fuel Gauge and Battery Monitor - STEMMA JST PH QT / Qwiic
·
The Adafruit LC709203F Fuel Gauge monitors your single-cell LiPo or Li-Ion battery and reports both voltage and state of charge as a percentage over I2C. It handles the non-linear voltage-to-percentage conversion for you, so your project always knows exactly how much battery is left — just like t...
Adafruit MAX17048 LiPoly / LiIon Fuel Gauge and Battery Monitor
·
The Adafruit MAX17048 LiPoly/LiIon Fuel Gauge and Battery Monitor gives you accurate battery voltage and charge percentage readings for your 1S 3.7–4.2V lithium polymer or lithium ion battery. Instead of guessing remaining capacity from a non-linear voltage curve, this smart sensor does the maths...
4-JSTPH 6
·
A 4-wire cable fitted with JST-PH 4-pin female connectors on each end, approximately 150mm (6") long. These compact, latching connectors are commonly used on STEMMA boards, small rechargeable battery packs, RC receivers, tiny cameras, and other small electronic devices. The JST-PH connector clic...
Adafruit Micro-Lipo Charger for LiPoly Batt with USB Type C Jack
·
The Adafruit Micro-Lipo Charger is a tiny, easy-to-use charger for single-cell 3.7V/4.2V lithium polymer and lithium ion rechargeable batteries. Simply plug a USB-C cable into any USB power source and connect your battery via the JST connector — two LEDs show charging status at a glance (red = ch...
JST-PH 2-pin Jumper Cable - 100mm long
·
We use 2 pin JST PH connectors for all our battery packs, and if you want to put a board in series, like our LC709203F Stemma QT battery gauge, this cable will be very handy! Both ends have a JST PH 2mm pitch 2-pin plug. Between the two, 100mm of color coded wire - red for power, black for gro...
TensorFlow Lite for Microcontrollers Kit
·
Machine learning has come to the 'edge' - small microcontrollers that can run a very miniature version of TensorFlow Lite to do ML computations. But you don't need super complex hardware to start developing your own TensorFlow models! We've curated a simple kit to dip your toes into machine ...
Adafruit 4x4 NeoTrellis Feather M4 Kit Pack
·
Build a handheld light-up button controller with this complete kit that pairs the Adafruit 4×4 NeoTrellis RGB Driver with a Feather M4 Express inside an elegant laser-cut acrylic enclosure. The 16 silicone buttons each have individually addressable NeoPixels underneath, and the seesaw I2C chip ha...
Adafruit Prop-Maker Starter Kit - Make your own Lightsaber!
·
The Adafruit Prop-Maker Starter Kit contains the electronics you need to build a 3D-printed NeoPixel lightsaber with motion-activated lighting and full sound effects. The kit pairs the Feather M4 Express with the Prop-Maker FeatherWing, giving you an accelerometer for swing and hit detection, a C...
2.0mm Pitch 3-pin Cable Matching Pair - JST PH Compatible
·
A matching pair of 3-pin JST PH compatible cables with inline plug and socket connectors. Each cable is 20 cm long with stranded 26 AWG wires, providing a reliable and compact connection that can carry a couple of amps of current. The friction-lock connectors make it easy to connect and disconne...
Bare Conductive Touch Board
The Touch Board from Bare Conductive is an easy-to-use Arduino@Heart board that gives you the ability to turn almost any material or surface into a sensor. Each Touch Board offers 12 electrodes for your a conductive ink or other type of connector that can be drawn or attached to create light s...
3 x AA Battery Holder with On/Off Switch, JST, and Belt Clip
·
A compact 3×AA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making it an ideal non-rechargeable alternative for 3.3V projects that use a JST batte...
JST-PH 2-Pin SMT Right Angle Breakout Board
·
A simple 2-pin connector soldered onto a breadboard-friendly breakout. This is compatible with the "JST PH 2-pin" connector. Mates perfectly with all our 1-cell LiPoly and LiIon batteries as well as our 6V coin cell holder and 3xAAA battery pack. We also have simple JST pigtails that mate w...
2 x AAA Battery Holder with On/Off Switch JST PH Connector
·
A slim 2×AAA battery holder with a built-in on/off switch and genuine JST PH connector. Two AAA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and portable builds. The JST PH connector polarity matches Adafruit's Li-Ion/LiPo ...
2 x AA Battery Holder with On/Off Switch JST PH Connector
·
A slim 2×AA battery holder with a built-in on/off switch and genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and portable builds without needing to disconnect the battery to turn off power. The...
2 x AAA Open Battery Holder with JST PH Connector
·
A slim, open-top 2×AAA battery holder with a genuine JST PH connector. Two AAA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and boards with JST PH battery inputs. The JST PH connector polarity matches Adafruit's Li-Ion/LiPo...
2 x AA Open Battery Holder with JST PH Connector
·
A slim, open-top 2×AA battery holder with a genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, Adafruit boards, and microcontrollers with JST PH battery inputs. The JST PH connector polarity matches Adafruit's Li-I...
TinyPICO ESP32 Development Board with USB-C
·
TinyPICO is the world's smallest fully-featured ESP32 development board, packing dual-core 240MHz processing, Wi-Fi, Bluetooth, and 4MB of PSRAM into a package smaller than your thumb. This is the V2 USB-C edition with MicroPython pre-installed and ready to go. Designed by UnexpectedMaker, every...
Adafruit Proto Doubler PiCowbell for Pico and PicoW
·
The Adafruit Proto Doubler PiCowbell gives your Raspberry Pi Pico or Pico W two side-by-side socket slots — plug in your Pico on one side and a PiCowbell accessory on the other, no soldering or stacking headers required. It also adds LiPo battery charging, a power switch, reset button, STEMMA QT ...
micro:bit Battery Holder - 2xAAA (JST-PH)
This two-cell AAA battery holder is made for powering BBC micro:bit projects without needing to stay tethered to USB.The attached 6" (~150mm) lead is terminated with a JST-PH connector that mates with the JST socket on the micro:bit, making it simple to add portable power to your build.Note: JST ...
