All Products

SKU: AF-6065 · MPN: ADA6065

The Adafruit CP2105 Friend provides two independent UART serial ports from a single USB-C connection — no USB hub required. Built around the Silicon Labs CP2105 dual-port bridge, it enumerates as two separate COM ports when plugged in, giving you an Enhanced port and a Standard port with differen...

SKU: AF-3343

The Adafruit CRICKIT FeatherWing is a robotics and electronics driver board that plugs into any Feather mainboard. It adds motor drivers, servo outputs, capacitive touch inputs, NeoPixel control, and an audio amplifier — all managed over I2C via the Adafruit seesaw co-processor, so it only uses t...

SKU: AF-3093

The Adafruit CRICKIT for Circuit Playground Express is a robotics and electronics driver board that bolts directly onto a Circuit Playground Express. It adds motor drivers, servo outputs, capacitive touch inputs, NeoPixel control, and an audio amplifier — all managed over I2C via the Adafruit see...

SKU: AF-3928

The Adafruit CRICKIT for micro:bit is a robotics and electronics driver board designed for the BBC micro:bit. Plug your micro:bit into the 40-pin edge connector and start controlling motors, servos, solenoids, NeoPixels, capacitive touch sensors, and a speaker — all managed over I2C via the Adafr...

SKU: AF-3957

The Adafruit CRICKIT HAT is a robotics and electronics driver board that plugs directly onto any Raspberry Pi with a 2×20 GPIO header. It adds motor drivers, servo outputs, capacitive touch inputs, a level-shifted NeoPixel driver, and a 3W I2S audio amplifier — all managed over I2C via the Adafru...

SKU: AF-5785

The Adafruit CSI/DSI Cable Adapter Thingy converts between the 15-pin 1.0mm pitch camera/display connector found on full-size Raspberry Pi boards and the 22-pin 0.5mm pitch connector used on the Pi Zero and CM4 development boards. It handles all the pin rearranging automatically — just snap in tw...

SKU: AF-3671

The Adafruit CSI/DSI Cable Extender Thingy lets you connect two 15-pin 1.0mm pitch flex cables end-to-end, extending the cable length for your Raspberry Pi Camera (CSI) or Display (DSI) connection. It handles all the pin rearranging automatically — just snap in two cables and go. Key Features ...

SKU: AF-4862

The Adafruit CYBERDECK Bonnet is a GPIO extender for the Raspberry Pi 400 that lets you plug any Pi bonnet, mini-HAT, or pHAT into the back of the Pi 400 at an angled position. It duplicates every GPIO pin from input to output, so your add-on boards work without any pin limitations. In addition ...

SKU: AF-4863

The Adafruit CYBERDECK HAT is a GPIO extender for the Raspberry Pi 400 that lets you plug full-size HAT displays and add-on boards into the back of the Pi 400 at a convenient angle. It duplicates every GPIO pin from input to output, so your HATs work without any pin limitations. In addition to t...

SKU: AF-6258 · MPN: ADA6258

The Adafruit DAC6578 Breakout provides eight independent 10-bit digital-to-analogue converters in a single package, all controllable over I2C. Set precise output voltages on up to eight channels simultaneously, making it ideal for multi-channel voltage control, LED dimming, or sensor calibration....

SKU: AF-6223 · MPN: ADA6223

The Adafruit DAC7578 Breakout provides eight independent 12-bit digital-to-analogue converters in a single package, all controllable over I2C. Set precise output voltages on up to eight channels simultaneously, making it ideal for multi-channel voltage control, LED dimming, or sensor calibration....

SKU: AF-5882 · MPN: ADA5882

The Adafruit DC Power BFF Add-On lets you power your QT Py or Xiao development board from a DC source up to 20V. The on-board MPM3610 integrated buck converter steps down the input to 5V at up to 1A, with no heat sink required — providing plenty of power for LEDs, WiFi, displays, and small motors...

SKU: AF-4280

The Adafruit DC & Stepper Motor Bonnet drives up to 4 DC motors or 2 stepper motors from your Raspberry Pi, with full PWM speed control. It uses a dedicated PWM driver chip over I2C, so only two pins (SDA/SCL) are needed — leaving the rest free for other I2C devices or HATs. The TB6612 MOSFET mo...

SKU: AF-2348

The Adafruit DC & Stepper Motor HAT drives up to 4 DC motors or 2 stepper motors from your Raspberry Pi, with full PWM speed control. It uses a dedicated PWM driver chip over I2C, so only two pins (SDA/SCL) are needed — leaving the rest free for other I2C devices or HATs. The TB6612 MOSFET motor...

SKU: AF-2328

Adafruit DotStar LED strips use 2-wire SPI instead of the single-wire protocol used by NeoPixels, allowing much faster data rates (up to 32 MHz) and a 20 KHz PWM refresh rate. This makes DotStars ideal for persistence-of-vision (POV) projects and smooth, flicker-free animations — especially at lo...

SKU: AF-2241

Adafruit DotStar LED strips use 2-wire SPI instead of the single-wire protocol used by NeoPixels, allowing much faster data rates (up to 32 MHz) and a 20 KHz PWM refresh rate. This makes DotStars ideal for persistence-of-vision (POV) projects and smooth, flicker-free animations — especially at lo...

SKU: AF-2237

The Adafruit DotStar Digital LED Strip (30 LED/m, black flex PCB) delivers superior performance over traditional NeoPixels with its 2-wire SPI interface. Push data at up to 32 MHz clock speed with no critical timing requirements, making it compatible with virtually any microcontroller or micropro...

SKU: AF-2239

The Adafruit DotStar Digital LED Strip (60 LED/m, black flex PCB) delivers superior performance over traditional NeoPixels with its 2-wire SPI interface. Push data at up to 32 MHz clock speed with no critical timing requirements, making it compatible with virtually any microcontroller or micropro...

SKU: AF-2329

The Adafruit DotStar Digital LED Strip (144 LED/m, white flex PCB) delivers superior performance over traditional NeoPixels with its 2-wire SPI interface. Push data at up to 32 MHz clock speed with no critical timing requirements, making it compatible with virtually any microcontroller or micropr...

SKU: AF-2242

The Adafruit DotStar Digital LED Strip (144 LED/m, white flex PCB) delivers superior performance over traditional NeoPixels with its 2-wire SPI interface. Push data at up to 32 MHz clock speed with no critical timing requirements, making it compatible with virtually any microcontroller or micropr...