All Products

SKU: AF-4200

The Adafruit PyBadge is a credit-card-sized all-in-one development board with a colour TFT display, game-style buttons, NeoPixels, sensors, and a speaker. Powered by the ATSAMD51 running at 120 MHz with 512 KB Flash and 192 KB RAM, it can run MakeCode Arcade games, CircuitPython programs, or Ardu...

SKU: AF-6396 · MPN: ADA6396

This bare eInk/ePaper display is a large 7.5 inch monochrome panel with 800 x 480 pixels, designed for low-power projects where the image needs to stay visible even after power is removed.Electronic paper displays are high contrast and easy to read in daylight, giving a paper-like look that suits...

SKU: AF-3538

Add heat-vision to your project with the Adafruit AMG8833 Grid-EYE Breakout. This sensor from Panasonic contains an 8×8 array of infrared thermal sensors that returns 64 individual temperature readings over I2C — like a compact thermal camera you can integrate into any microcontroller or Raspberr...

SKU: AF-3406

The Feather nRF52 Bluefruit LE is an all-in-one Bluetooth Low Energy development board built around the Nordic nRF52832. Unlike earlier Bluefruit Feathers that used a separate helper chip, the nRF52832 runs your application code and handles BLE directly — resulting in lower power consumption, low...

SKU: AF-3315

A 2.4" TFT touchscreen display shield for the Adafruit Feather ecosystem. Featuring a 320×240 pixel display with 16-bit colour, a resistive touchscreen, and a built-in microSD card slot, this FeatherWing adds a full interactive display to any Feather board via SPI. Comes fully assembled with dua...

SKU: AF-2945

The NeoPixel FeatherWing adds a 4×8 matrix of 32 individually addressable RGB LEDs to any Adafruit Feather board. Using Feather stacking headers or female headers, the wing connects directly on top or bottom of your Feather for a compact, colourful display. Only one pin is required to control al...

SKU: AF-3957

The Adafruit CRICKIT HAT is a robotics and electronics driver board that plugs directly onto any Raspberry Pi with a 2×20 GPIO header. It adds motor drivers, servo outputs, capacitive touch inputs, a level-shifted NeoPixel driver, and a 3W I2S audio amplifier — all managed over I2C via the Adafru...

SKU: AF-3928

The Adafruit CRICKIT for micro:bit is a robotics and electronics driver board designed for the BBC micro:bit. Plug your micro:bit into the 40-pin edge connector and start controlling motors, servos, solenoids, NeoPixels, capacitive touch sensors, and a speaker — all managed over I2C via the Adafr...

SKU: AF-1910

The Adafruit 14-Segment LED Alphanumeric Backpack is a standalone I2C LED driver board that makes it easy to add a 4-character alphanumeric display to any project. Powered by the HT16K33 chip, it handles all LED multiplexing over I2C — just send commands and it lights up the right segments for yo...

SKU: AF-3975

Drive up to 8 strands of NeoPixels simultaneously with DMA — no more blocking your code to push pixel data. The NeoPXL8 Friend is a standalone level-shifting breakout board that converts 3.3 V logic to 5 V for 8 independent NeoPixel outputs, with a breadboard-friendly form factor that works with ...

SKU: AF-3093

The Adafruit CRICKIT for Circuit Playground Express is a robotics and electronics driver board that bolts directly onto a Circuit Playground Express. It adds motor drivers, servo outputs, capacitive touch inputs, NeoPixel control, and an audio amplifier — all managed over I2C via the Adafruit see...

SKU: AF-4197

Add a crisp, paper-like display to your microcontroller project with the Adafruit 2.13" Monochrome eInk Breakout. This 250×122 pixel black-and-white eInk panel delivers excellent daylight readability and retains its image even with power completely disconnected — just like printed paper. An onbo...

SKU: AF-4242

The Adafruit PyGamer is a pocket-sized, open-source gaming handheld built for DIY game development and retro emulation. Powered by the ATSAMD51 running at 120 MHz with 512 KB flash and 192 KB RAM, it features an analog thumbstick, six tactile buttons, a colour TFT display, and stereo audio — all ...

SKU: AF-4277

Everything you need to build a pocket-sized gaming handheld — no soldering required. This starter kit bundles the Adafruit PyGamer with a rechargeable battery, acrylic enclosure, speaker, button caps, and a zipper carry case. The PyGamer is powered by the ATSAMD51 (120 MHz ARM Cortex-M4) with 51...

SKU: AF-4285

Give your Arduino project WiFi connectivity with the Adafruit AirLift Shield. This shield uses an ESP32 as a WiFi co-processor, handling all the heavy lifting of network connections and TLS/SSL encryption so your main microcontroller can focus on your application logic. The ESP32 communicates ov...

SKU: AF-3243

A Feather board without ambition is a Feather board without FeatherWings! This is the Fully assembled (with headers) DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 stepper and 2 DC motors). Using our Feather Stacking Headers or Fea...

SKU: AF-1028

Add a large, vibrant tri-colour eInk display to your microcontroller project with this 2.9" breakout board. The panel displays red, black, and white pixels at 296×128 resolution that remain visible even with power completely disconnected — just like printed paper, but with the added impact of col...

SKU: AF-4687

The Adafruit 2.13" Monochrome E-Ink Bonnet brings crisp, paper-like displays to your Raspberry Pi with no soldering required. Simply plug this pre-assembled bonnet onto any Pi with a 2×20 header and start displaying high-contrast black-and-white graphics that remain visible even with power discon...

SKU: AF-4947

The Adafruit 2.13" Tri-Colour eInk Display brings electronic paper technology to your microcontroller projects. Featuring a 250×122 pixel display with black, red, and white ink, this breakout delivers high-contrast, daylight-readable visuals that persist even when power is completely disconnected...

SKU: AF-5724

The Adafruit RP2040 CAN Bus Feather combines the powerful RP2040 microcontroller with an MCP25625 CAN controller and transceiver, giving you a ready-to-go CAN Bus interface in the compact Feather form factor. No soldering is needed to get started — just connect your CAN Bus lines to the included ...