All Products

SKU: AF-2379

A USB-A to Micro-B power-only cable with a built-in inline on/off switch. Perfect for powering a Raspberry Pi or any Micro USB device from a USB power supply, with the convenience of a physical power switch — no need to unplug the cable to turn your device on or off. Key Features Inline On/Off...

SKU: DF-SEN0279

The MB1414 USB-ProxSonar-EZ1 is an ultrasonic proximity and range sensor with a USB interface. It provides both proximity detection (target enter/exit a calibrated zone) and distance measurement with 1-inch resolution, making it ideal for people sensing and obstacle detection applications. With ...

SKU: LB-LS2193

A clip-on LED desk light with adjustable brightness and colour temperature, ideal for illuminating soldering work, electronics projects, or general desk tasks. The centre hole lets you look through the light ring while working, keeping your view unobstructed. Key Features 3 Brightness Levels –...

SKU: DF-DFR0173

A low power version of the USB-RLY16 module, the USB-RLY16L is powered solely from the USB bus and provides eight volt free contact relay outputs with a current rating of up to 16Amp each. The relays are SPCO (Single Pole Change Over) types and provide position 0, position 1 and common pins (latc...

SKU: EC-MCP00101P

This USBSerial Adapter is a compact USB to serial adapter equipped with BEE (20pin 2.0mm) sockets. With integrated FT232 IC, It can do many things such as used for programming(Arduino Pro Mini), debug some hardware or communicating with MCU applications. On the other hand, you may connect your...

SKU: AF-18

This USB-to-serial converter adds a DB9 RS-232 serial port to your computer via USB. Based on the FTDI FT232RL chip, it delivers true RS-232 voltage levels (approximately ±10V) rather than TTL 5V — ensuring compatibility with older devices like GPS receivers, handheld programmers, and other equip...

SKU: DF-DFR0164

This is a new version of the FTDI breakout board features an Atmega8U2 programmed as a USB-to-serial converter, the same chip found on the Arduino Uno. The 8U2 firmware uses the standard USB COM drivers, and no external driver is needed. However, on some Windows systems installing the drive...

SKU: LB-LS0040

Power your next project using the Australian Sun with this solar panel. The panel is capable of 3.5 watts in the open sun with a peak power output around 6V at 580-600mA. 6v 3.5w 580-600MA  High conversion rate, high efficiency output
. Operating voltage: 6v 
Power: 3.5W
 Work: cur...

SKU: DF-FIT0870

A USB to DC boost converter cable that steps up 5 V from a USB power source to either 9 V or 12 V output, selectable via a built-in switch. A digital LED display shows the current output voltage. Simply plug the USB end into a power bank, USB charger, or any 5 V USB source to power 9 V or 12 V de...

SKU: DF-DFR0116

This is a USB AVR programmer supported by offical Arduino IDE. Once the Arduino has lost its bootloader for some reasons, use this programmer to reburn the bootloader and save the dead Arduino. This programmer works really well for ATmega168 and ATmega328 and should work with all the AVR micros ...

SKU: AF-2778

This cable is kinda fascinating - it has an integrated boost converter, so you can plug it into any USB port (from a computer, battery pack, etc) and it will give you a higher DC voltage! It's a handy way to power 12V powered devices with a center-positive 2.1mm DC barrel jack from a USB port....

SKU: AF-2777

This USB to DC booster cable has an integrated boost converter that steps up 5V USB power to 9V DC, output through a centre-positive 2.1 mm barrel jack. It's a convenient way to power 9V devices from any USB port — whether from a computer, USB wall charger, or battery pack. Rated for 500 mA cont...

SKU: AF-2697

This USB to 2.1 mm barrel jack cable lets you power 5 V DC devices from any USB port. Simply connect the USB-A end to a computer, USB wall adapter, or USB battery pack, and the barrel jack end to your device. At 1 metre long with 22 AWG wires, it handles higher current draws reliably. The barrel...

SKU: AF-5457

This cable is kinda fascinating - it has an integrated boost converter, so you can plug it into any USB port (from a computer, battery pack, etc), and it will give you a higher DC voltage! It's a handy way to power a 9V or 12V device. Unlike our other 'USB booster' cables, this one comes with ...

SKU: SF-COM-14567

It’s tiny, it’s handy, and it can give your normal USB-equipped device a micro-B connector! With the USB to Micro-B Adapter you can make a flash drive connect to your tablet, connect a keyboard to your phone in order to text with ease, attach a Bluetooth® dongle to your RPi Zero, and more! S...

SKU: AF-5994 · MPN: ADA5994

No matter what serial-esque protocol you need to interface with, this USB to Multi-Protocol Serial adapter cable will be able to get this-connected-to-that. It supports RS232 serial, TTL UART serial, RS485 and RS422. All with quick-connecting screw terminals so you don't need to do any soldering ...

SKU: DF-FIT0272

The USB 2.0 to RS422/RS485 Cable provides a simple and easy to connect between the USB and RS422/RS485 ports interface. Ideally for PC, thin client or servers to provide instant RS422/RS485 ports expansion via USB ports. USB to RS422/RS485 industrial intelligent converter,no power supply nee...

SKU: DF-FIT0737

This USB to RS485 converter module( USB 1.1，USB 2.0，USB 3.0 compatible) can expand one RS485 asynchronous communication interface from a computer’s USB interface to realize the communication between PC and other RS485 devices.The module uses a PL2303 chip and an easy-to-install driver. There are ...

SKU: DF-FIT0874

RS485 serial ports are often used to enable communication between PC and RS485 devices. This USB to RS485 serial cable with built-in a CH340 bus converter chip allows direct communication between PC and 485 device without extra wire connection. The converter works well with WindowsXP/Vista/7/8/10...

SKU: SF-DEV-11814

The µUSB-PA5 is a compact USB-to-Serial TTL UART bridge based on the FTDI FT232RQ. It connects to your PC via a Mini-B USB connector and provides serial communication at baud rates up to 3 Mbps — designed primarily for programming and communicating with 4D Systems displays and controllers. The 5...