Little Bird
Electronics Starter Kit
Content Listing 1. 1x Triaxial Accelerometer Sensor Module (ADXL345)2. 1x DHT-11 (Digital Temperature & Humidity Sensor)3. 1x Ultrasonic Distance Sensor Mod...
Content Listing
1. 1x Triaxial Accelerometer Sensor Module (ADXL345)
2. 1x DHT-11 (Digital Temperature & Humidity Sensor)
3. 1x Ultrasonic Distance Sensor Module
4. 1x PIR Movement Sensor
5. 1x PS2 Joystick Module
6. 1x LCD1602
7. 1x Servo
8. 1x Stepper Motor
9. 1x Stepper Motor Driver Module (Based on ULN2003A)
10. 1x ADC0832
11. 1x L9110 Motor Driver
12. 1x DC Motor
13. 1x 4x4 Matrix Keyboard
14. 1x Breadboard Power Supply Module
15. 1x 40-pin GPIO Extension Board
16. 1x 40-pin GPIO Cable
17. 2x Light Sensor (Photoresistor)
18. 2x Analog Temperature Sensor (Thermistor)
19. 1x Relay
20. 1x Active Buzzer
21. 1x Passive Buzzer
22. 1x 7-Segment Display
23. 1x 4-bit 7-Segment Display
24. 1x LED Bar Graph Display
25. 1x Dot-Matrix Display
26. 2x 74HC595
27. 2x Switch
28. 1x RGB LED
29. 8x Red LED
30. 4x Green LED
31. 4x Yellow LED
32. 4x Blue LED
33. 4x Button (Large)
34. 5x Button (Small)
35. 1x Button Cap (Red)
36. 1x Button Cap (White)
37. 2x Button Cap (Blue)
38. 16x Resistor (220Ω)
39. 10x Resistor (1kΩ)
40. 10x Resistor (10kΩ)
41. 2x Potentiometer (10kΩ)
42. 5x Capacitor (104)
43. 4x Capacitor (10uF)
44. 2x 1N4148 Diode
45. 2x 1N4001 Diode
46. 4x NPN Transistor (8050)
47. 4x PNP Transistor (8550)
48. 1x Breadboard
49. 40x Male-to-Male Jumper Wires
50. 20x Male-to-Female Jumper Wires
51. 20x Female-to-Female Jumper Wires
52. 1x Header (40-pin)
53. 1x Band Resistor Card
54. 1x Project Box
Jargon buster
Plain-language definitions for the technical terms used above.
- GPIO
- General-purpose input/output pins are microcontroller pins you can set in software to read signals, switch devices on and off, or connect to peripherals. The number of GPIO pins matters because it limits how many buttons, LEDs, sensors, and other parts you can wire directly to the board.
- LED
- A light-emitting diode is a small electronic component that lights up when current flows through it in the correct direction. In this kit, LEDs create the flashing effect, so polarity and correct soldering matter for the project to work.
- male-to-male
- A male-to-male cable has plug-style connectors on both ends rather than a socket on one end. This matters when choosing a cable because it must match the female sockets on the modules or boards you want to connect.
- motor driver
- An electronic circuit that lets a low-power controller switch and control a motor that needs more current than the controller pins can safely provide. Checking motor driver support matters because pumps and motors usually cannot be connected directly to a microcontroller output.
- photoresistor
- A light-sensitive resistor whose resistance changes depending on how much light hits it. It matters for projects such as night-lights and light alarms because it gives a simple way for a microcontroller to sense brightness.
- potentiometer
- A variable resistor usually turned with a knob or shaft to create an adjustable electrical signal. It is often used for inputs such as volume, brightness or position, so it helps beginners learn how a microcontroller reads changing values.
- RGB
- Short for red, green and blue, usually referring to an LED that can mix those three colours. It matters because controlling an RGB LED teaches how separate outputs combine to create different colours.
- servo
- A servo is a motor with built-in position control, usually told to move to a specific angle by a control signal. It matters when you need repeatable movement, such as steering, arms, flaps, or linkages, rather than continuous spinning.
Find this product in
Related Tutorials
Free guides on learn.littlebird.com.au
