Adafruit
64x64 RGB LED Matrix Panel with 45 Degree Curb-Cut - 2.5mm Pitch
The 64×64 RGB LED Matrix Panel with 45° Curb-Cut corners and 2.5mm pitch features 4096 bright RGB LEDs in an ultra-high-density panel. The curb-cut corners a...
Get notified when back in stock
The 64×64 RGB LED Matrix Panel with 45° Curb-Cut corners and 2.5mm pitch features 4096 bright RGB LEDs in an ultra-high-density panel. The curb-cut corners are angled at 45°, allowing multiple panels to be assembled into LED video cubes or rectangular enclosures with seamless edges.
This panel uses a non-standard 5-address (ABCDE) multiplexing system. Many standard drivers only support 4-address (ABCD) setups. Compatible controllers include the RGB Matrix Bonnet for Raspberry Pi, RGB Matrix HAT (both require a solder jumper), and Matrix Portal (jumper required). Arduino shields with the Adafruit library and HDMI driver boards do not support 5-address multiplexing. The SmartLED Shield with Teensy 3.5/3.6 has the hardware for 5-address panels and sufficient RAM, but the power plug must be manually soldered or adapted due to shield overlap.
Key Features
- 45° Curb-Cut Corners – Angled edges allow panels to be assembled into cubes and rectangular enclosures
- 2.5mm Pixel Pitch – Ultra-high density for sharp detail at close viewing distances
- 4096 RGB LEDs – 64×64 resolution with full-colour output
- 5-Address Multiplexing – ABCDE system for 64-pixel tall panels
- Chainable – IDC input/output connectors allow multiple panels to be daisy-chained
Specifications
- Pixel Pitch: 2.5mm
- Resolution: 64×64 (4096 LEDs)
- Operating Voltage: 5V
- Corner Cut: 45°
Also Available
- 64×64 RGB LED Matrix Panel – 2mm Pitch
- 64×64 RGB LED Matrix – 2.5mm Pitch
- 64×64 RGB LED Matrix – 3mm Pitch
- 64×64 RGB LED Matrix Panel – 3mm Pitch (DFRobot)
Ideal For
- LED video cubes and rectangular display enclosures
- Multi-panel installations requiring seamless corners
- Close-range indoor displays and signage
- Raspberry Pi projects using the RGB Matrix Bonnet or HAT
Package Contents
- 1× 64×64 RGB LED Matrix Panel with 45° curb-cut corners (2.5mm pitch)
- 1× IDC ribbon cable
- 1× Power cable
Jargon buster
Plain-language definitions for the technical terms used above.
- HDMI
- HDMI is a common digital video and audio connection used by computers, media players, and many displays. If a display kit has HDMI input, it is usually much easier to test with a single-board computer because it can act like a normal monitor.
- LED
- A light-emitting diode (LED) is a small electronic component that emits light when current flows through it in the correct direction. Because it only conducts one way, its polarity matters, and a through-hole LED must be soldered the correct way around to light up.
- RAM
- RAM (random-access memory) is fast, temporary memory a device uses for working data while it is running; in its common volatile form, its contents are lost when power is removed. Some devices offer a mode that applies settings to RAM only, which is handy for testing changes temporarily because they are not stored permanently and disappear at power-off.
- RGB
- Short for red, green and blue, the three primary colours of light that are mixed in varying amounts to make a wide range of colours. In electronics RGB can refer to an LED or pixel that blends these three colours, or to a colour signal or interface that carries separate red, green and blue channels.
- Shield
- An add-on board that plugs into a main controller board to give it extra features such as sensing, motor control or communication. Knowing a product supports shields helps you judge whether it can connect neatly into an existing maker-board setup.
- solder jumper
- A solder jumper is a small pair or group of pads on a circuit board that can be bridged or cut with solder to change a hardware setting. It matters because changing modes may require careful soldering rather than just changing software.
Find this product in
Brands
Displays & Screens
Related Tutorials
Free guides on learn.littlebird.com.au
