Wearable Tech & E-textiles

SKU: AF-1361 | Brand: Adafruit

This conductive material, also known as Velostat or Linqstat, is a handy addition to a wearable and sensor hacking toolkit. It is pressure-sensitive, so squeezing the sheet reduces its resistance, making it useful for...

SKU: LB-LR0214-37 | Brand: Little Bird

Other Features: Voltage: 3V / 5V; Amplification factor: 330; Wavelength: 609nm; A product for Arduino.1 x   Pulse sensor Pulse Heart Rate Sensor Module  

SKU: SF-SEN-12650 | Brand: SparkFun

The AD8232 SparkFun Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as a...

SKU: SF-SEN-10264 | Brand: SparkFun

A simple flex sensor 2.2" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the original Nintendo Power Gl...

SKU: SF-SEN-08606 | Brand: SparkFun

A simple flex sensor 4.5" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the original Nintendo Power Gl...

SKU: SF-SEN-12969 | Brand: SparkFun

A 10-pack of disposable biomedical sensor pads (electrodes) for measuring EEG, ECG, and EMG signals. Each pad features integrated latex-free gel for strong skin adhesion and a snap connector that attaches easily to el...

SKU: DF-SEN0064 | Brand: DFRobot

A simple flex sensor 4.5" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the original Nintendo Power Gl...

SKU: SF-SEN-09673 | Brand: SparkFun

A compact force sensitive resistor (FSR) from Interlink Electronics with a 4 mm (0.16″) diameter active sensing area. The resistance changes based on applied pressure — from over 1 MΩ with no pressure down to approxim...

SKU: SF-DEV-18426 | Brand: SparkFun

The MyoWare® 2.0 Arduino Shield is designed to easily connect up to six MyoWare 2.0 Muscle Sensors and Link Shields using 3.5mm TRS-to-TRS audio cables. The board comes pre-populated with male headers so all you would...

SKU: AF-1093 | Brand: Adafruit

Pulse Sensor Amped is a greatly improved version of the original Pulse Sensor, a plug-and-play heart-rate sensor for Arduino and Arduino compatibles. It can be used by students, artists, athletes, makers, and game & m...

SKU: AF-182 | Brand: Adafruit

This sensor can detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface.These sensors are easy to use, they are basically resistors that change ...

SKU: SF-DEV-18425 | Brand: SparkFun

The MyoWare 2.0 Link Shield connects a MyoWare 2.0 Muscle Sensor to your Arduino microcontroller via a 3.5mm TRS cable. Simply snap the Link Shield onto your Muscle Sensor using the built-in snap connectors, connect a...

SKU: AF-4300 | Brand: Adafruit

The Adafruit HalloWing M4 Express is a skull-shaped development board powered by the ATSAMD51G18 — a 120 MHz Cortex M4 processor with 512 KB Flash and 192 KB RAM. Featuring a 1.54" IPS TFT display (240×240 pixels), a ...

SKU: PI-PSA001 | Brand: Pimoroni

The Pulse Sensor Amped is a plug-and-play heart-rate sensor for Arduino. It detects pulse by measuring changes in reflected light as blood pumps through your tissues, providing a real-time analogue signal that fluctua...

SKU: PL-1696 | Brand: Pololu

This force-sensing resistor (FSR) from Interlink Electronics is a passive component that exhibits a decrease in resistance when there is an increase in the force applied to the 0.58″-diameter (1.5 cm) active area...

SKU: DF-SEN0086 | Brand: DFRobot

A simple flex sensor 2.2" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the original Nintendo Power G...

SKU: AF-4343 | Brand: Adafruit

The Adafruit MONSTER M4SK is a dual-display development board designed for creating animated electronic eyes for costumes, props, and interactive projects. Powered by a 120 MHz ATSAMD51 Cortex M4 processor, it drives ...

SKU: PI-AT-04-001 | Brand: Pimoroni

The MyoWare Muscle Sensor is an all-in-one electromyography (EMG) sensor that measures the filtered and rectified electrical activity of a muscle. It outputs 0 V to Vs (supply voltage) depending on the level of activi...

SKU: DF-SEN0065 | Brand: DFRobot

This is a small force sensitive resistor. It has a 0.16" (4 mm) diameter active sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the fo...