SparkFun

SKU: SF-CAB-14303 | Brand: SparkFun

A 10-pack of cables with an alligator clip on one end and a bare hookup pigtail (male pin) on the other. These cables make it easy to connect alligator clips directly into breadboards, development boards, and any stan...

SKU: SF-PRT-14411 | Brand: SparkFun

The SparkFun LiPo Charger/Booster is a compact board that charges a single-cell lithium polymer battery and boosts its output to a regulated 5V at up to 1A. Built around the MCP73831 charge controller and PAM2401 boos...

SKU: SF-PRT-14380 | Brand: SparkFun

The SparkFun Adjustable LiPo Charger is a single-cell lithium polymer (LiPo) and lithium ion battery charger. Because it’s adjustable, this charger will be able to safely charge most of our single-cell batteries ...

SKU: SF-PRT-14338 | Brand: SparkFun

This isn’t your ordinary power supply. The Global Power Supply is a 15V, 4.34A power device specifically designed to work with the JustBoom Amp HAT for the Raspberry Pi. Additionally, as this is a “global” power su...

SKU: SF-COM-14325 | Brand: SparkFun

A basic 125 kHz RFID tag with a unique 40-bit ID, ideal for access control, identification, and automation projects. The tag uses the EM4001 ISO-based RFID IC with Manchester encoding. This blank, smooth, credit-card...

SKU: SF-PRT-14321 | Brand: SparkFun

A standard 1×12 female header designed for the Particle Photon and Photon ProtoShield boards. Add reliable, stackable connectivity to your next Photon project with this 0.1" (2.54mm) pitch header. While designed for ...

SKU: SF-PRT-14313 | Brand: SparkFun

This Digital LED Voltmeter measures the voltage at a particular point of the system it has been hooked up to and then provides a readout on its three 7-segment LEDs. This voltmeter is able to provide a readout of volt...

SKU: SF-ROB-09347 | Brand: SparkFun

Here, for all your mechatronic needs, is a simple, high quality continuous continuous rotation servo motor. This servo is able to take in 6 volts and deliver 66.7 oz-in. of maximum torque at 70 r/min. A standard 3-p...

SKU: SF-BOB-09322 | Brand: SparkFun

A simple breakout PCB for the GP1A57HR photo interrupter (also known as a photogate, photodiode, or phototransistor). This PCB has three connections for PWR, GND, and Signal.When the gate is clear, SIG will be high (>...

SKU: SF-DEV-14285 | Brand: SparkFun

The SparkFun Wireless Motor Driver Shield is designed to make connecting motors, sensors and other components to your Arduino-based project as fast and easy as possible. The heart of the Wireless Motor Driver Shield i...

SKU: SF-SEN-14282 | Brand: SparkFun

This S-Type load cell (sometimes called a strain gauge) can translate up to 200kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response and...

SKU: SF-WRL-09232 | Brand: SparkFun

This is an adapter that converts an RP-SMA board to an SMA antenna. The adapter will connect to any of our 2.4GHz wireless boards (Bluetooth, Nordic, or XBee) or interface cables and will allow you to use an ant...

SKU: SF-WRL-09233 | Brand: SparkFun

The SMA Male to RP-SMA Male Adapter converts between SMA and RP-SMA connector types, making it easy to pair antennas and cables that use different threading configurations. One end features a standard SMA male connect...

SKU: SF-ROB-09238 | Brand: SparkFun

This is a simple, but very powerful stepper motor with a 4-wire cable attached. This is a Bipolar Motor. Features: Step Angle (degrees) :1.8 2 Phase Rated Voltage : 12V Rated Current : 0.33A Holding Torque : 2.3k...

SKU: SF-ROB-12285 | Brand: SparkFun

This compact micro gearmotor features a full metal gear train with a 298:1 ratio, delivering high torque in a small form factor. Operating from 6–12V, it provides up to 90 RPM and 70 oz·in of stall torque, making it i...

SKU: SF-TOL-14235 | Brand: SparkFun

The Xcelite 8-in-1 Screwdriver Set provides eight high-quality bits in a single ergonomic tool. Each bit is easily accessible with a spring-loaded magnetic housing that holds the seven included bits you aren’t current...

SKU: SF-COM-09179 | Brand: SparkFun

A 33 mm round momentary pushbutton in arcade style with a convex green cap. Features a simple screw-in design for easy panel mounting — ideal for arcade builds, interactive projects, and control panels. Specification...

SKU: SF-PRT-09174 | Brand: SparkFun

These 33mm (1.3") spring loaded pogo pins are great for programming and applications where you don’t always want headers soldered onto your boards. We use them for our programming jigs in production. The pins fit snug...

SKU: SF-GPS-09123 | Brand: SparkFun

This is a 1 foot long JST SH communication cable which can be cut and hacked to your needs. Ideal if you have a UAV project where the GPS module may be a distance away from the controller board. Cable has two 6-pin JS...

SKU: SF-COM-09120 | Brand: SparkFun

This is the knob that connects to the linear slide potentiometer. Knob has a nice friction fit onto slide.Documents: Datasheet