SparkFun

SKU: SF-COM-16810 | Brand: SparkFun

The SparkFun Qwiic Dual Solid State Relay is a power delivery board that allows users to switch two AC loads from a low power microcontroller using the SparkFun Qwiic connect system. The board features two 25A/250VAC ...

SKU: SF-SEN-16761 | Brand: SparkFun

This 16 mm C-mount telephoto lens from CGL Electronics is designed for the Raspberry Pi HQ Camera Module. It produces 10 MP images in a 1" sensor format and is easily interchangeable using the thumb screw and C-CS ada...

SKU: SF-ROB-16836 | Brand: SparkFun

The SparkFun ProDriver makes it easy to start developing with the TC78H670FTG bipolar stepper motor driver from Toshiba! Latch terminals provide instant solder-less connections to every feature offered. Use our extens...

SKU: SF-SEN-16977 | Brand: SparkFun

The TFMini-S Micro LiDAR Module is a ToF (Time of Flight) LiDAR sensor capable of measuring the distance to an object as close as 10 centimeters (+/- 6cm up to 6m) and as far as 12 meters (+/-1% starting at 6m)! As wi...

SKU: SF-SEN-16294 | Brand: SparkFun

The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junc...

SKU: SF-PRT-16891 | Brand: SparkFun

This surface-mount 50-pin board-to-board connector with 0.5 mm pitch and double-slot male configuration is used on Alchitry FPGA boards. Soldered to the underside of a board, these connectors allow Alchitry FPGA board...

SKU: SF-SEN-16304 | Brand: SparkFun

The SparkFun TMP102 Qwiic breakout provides accurate digital temperature readings over I2C with minimal wiring. Based on the Texas Instruments TMP102, the sensor delivers 0.0625 °C resolution and ±0.5 °C accuracy, com...

SKU: SF-PRT-16890 | Brand: SparkFun

These are the surface mount 50 pin 0.5mm Board to Board Double Slot Female Connectors found on the Alchitry FPGA boards. These headers allow for Alchitry FPGA Boards to stack on one another by being soldered to the to...

SKU: SF-SEN-16467 | Brand: SparkFun

Looking to keep a log of the climate in your greenhouse, create a humidor control system or want to track temperature and humidity data for a weather station project? The SparkFun SHTC3 Humidity Sensor may be the perf...

SKU: SF-GPS-15712 | Brand: SparkFun

The SparkFun NEO-M9N GPS Breakout is a high quality, GPS board with equally impressive configuration options. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it can receive signals from the ...

SKU: SF-GPS-16329 | Brand: SparkFun

The SparkFun NEO-M8U GPS Breakout is a high quality, GPS board with equally impressive configuration options. The NEO-M8U takes advantage of u-blox's Untethered Dead Reckoning (UDR) technology. The module provides con...

SKU: SF-GPS-15733 | Brand: SparkFun

The SparkFun NEO-M9N GPS Breakout with on-board chip antenna is a high quality, GPS board with equally impressive configuration options. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it ca...

SKU: SF-DEV-16789 | Brand: SparkFun

The SparkFun Qwiic Shield for Arduino Nano provides you with a quick and easy way to enter into SparkFun's Qwiic ecosystem with your Arduino Nano board. The Qwiic shield connects the I2C bus (GND, 3.3V, SDA and SCL) o...

SKU: SF-DEV-16790 | Brand: SparkFun

The SparkFun Qwiic Shield for Thing Plus adds four Qwiic connectors (two horizontal, two vertical) to any Thing Plus or Adafruit Feather-format development board. It breaks out the I²C bus (GND, 3.3 V, SDA, SCL) to st...

SKU: SF-PRT-16538 | Brand: SparkFun

Poke Home Connectors have been featured on a number of our boards over the last few years by providing a simple screw-terminal-type connector for easy wire connection purposes. Similar to screw terminals, Poke Home Co...

SKU: SF-WRL-15836 | Brand: SparkFun

The SparkFun Pro RF is a LoRa®-enabled wireless board that marries a SAMD21 and a long-range RFM95W to make a compact and easy-to-use IoT Arduino board. With its fast MCU and excellent point to point data transmission...

SKU: SF-COM-16347 | Brand: SparkFun

The WS2812B (or "NeoPixel") may look like a common 5050-sized (5x5mm) SMD LED, but there’s actually an integrated control circuit embedded inside there too. Sometimes you don't need 10 or even 50, maybe you need a who...

SKU: SF-DEV-16260 | Brand: SparkFun

The Leopard Imaging Camera is a wide-angle camera module designed specifically for the NVIDIA Jetson Nano Developer Kit. With a 136° field of view, Sony IMX219 8.08 MP colour sensor, and CSI-2 MIPI 2-lane interface, i...

SKU: SF-PRT-15900 | Brand: SparkFun

You'll have no need for a screwdriver with this terminal! This is a 3-pin Latch Terminal with 5mm pitch pins. Each pin is rated up to 250V @ 11A and will line up well with the standard 0.1" spacing. Please note that t...

SKU: SF-PRT-15899 | Brand: SparkFun

You'll have no need for a screwdriver with this terminal! This is a 3-pin Latch Terminal with 5mm pitch pins. Each pin is rated up to 250V @ 11A and will line up well with the standard 0.1" spacing. Please note that t...