SparkFun

SKU: SF-BOB-12941 | Brand: SparkFun

With SD and MMC memory prices dropping, the time is right for mass storage and datalogging. This breakout board will allow you to breakout the SD/MMC socket to a standard .1" 10-pin header. Perfect for breadboarding a...

SKU: SF-DEV-12924 | Brand: SparkFun

The MicroView is the first chip-sized Arduino compatible module that lets you see what your Arduino is thinking using a built-in OLED display. This USB programmer connects directly to the MicroView and lets you not on...

SKU: SF-COM-10613 | Brand: SparkFun

A digital potentiometer that lets you control a voltage divider with serial signals from your microcontroller. Wire it up like a standard potentiometer, then use digital commands to adjust the wiper position — no mech...

SKU: SF-TOL-10602 | Brand: SparkFun

Precision curved tweezers with an ESD-safe coating, ideal for handling surface-mount components and other small electronic parts. The fine curved tip provides excellent control when placing or removing tiny components...

SKU: SF-COM-10597 | Brand: SparkFun

This plastic knob accepts a 6mm shaft and has a 15mm outer diameter. They simple press-fit onto a shaft. These are clear so that they can be used with our illuminated rotary encoders. Documents: Dimensional Drawing

SKU: SF-PRT-10592 | Brand: SparkFun

This is the SMD version of PRT-07948, which is the unit we like to use as RTC backup and SRAM backup for GPS units. Holds battery in place with friction. The metal housing connects to the positive side of the batte...

SKU: SF-WRL-10533 | Brand: SparkFun

A simple 315 MHz wireless receiver module that pairs with 315 MHz transmitters to create a basic one-way data link. It fits easily into a breadboard and works well with microcontrollers like Arduino for straightforwar...

SKU: SF-PRT-10512 | Brand: SparkFun

A snap-in 9V battery holder with a 5.5mm/2.1mm centre-positive barrel jack connector. The battery clicks securely into place, and three mounting holes allow you to attach the holder to an enclosure or chassis. Key Fe...

SKU: SF-COM-10468 | Brand: SparkFun

The MSGEQ7 is a CMOS graphic equaliser IC that divides the audio spectrum into seven frequency bands: 63 Hz, 160 Hz, 400 Hz, 1 kHz, 2.5 kHz, 6.25 kHz, and 16 kHz. Each band is peak-detected and multiplexed to provide ...

SKU: SF-ROB-10456 | Brand: SparkFun

This 12V DC solenoid valve controls water flow through a 3/4″ threaded inlet and outlet. It is normally closed — fluid is blocked until 12V is applied to the fast-on spade connectors on the solenoid coil. Connect it t...

SKU: SF-ROB-10455 | Brand: SparkFun

The SEAFLO mini water pump is a submersible 12 V pump capable of moving up to 1325 litres per hour (350 GPH). Powered by a heavy-duty 1.5 A motor housed in a tough thermoplastic body, it handles continuous operation i...

SKU: SF-PRT-12790 | Brand: SparkFun

This is a 2x23 pin female PTH header, with extra long legs which makes great for stacking. This piece is in the common configuration for Beaglebone Black headers. Each pin has a spacing of 0.1" in between each othe...

SKU: SF-ROB-10391 | Brand: SparkFun

A linear push-type solenoid rated for 36 V DC that also works well at 12 V. Solenoids produce linear motion for pushing, pulling, or actuating switches and levers. This unit has a measured throw of approximately 10 mm...

SKU: SF-PRT-10375 | Brand: SparkFun

This is a simple five wire cable. Great for jumping from board to board or just about anything else. There is a 5-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway hea...

SKU: SF-PRT-10372 | Brand: SparkFun

This is a simple two wire cable. Great for jumping from board to board or just about anything else. There is a 2-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers...

SKU: SF-PRT-10361 | Brand: SparkFun

This is a simple six wire cable. Great for jumping from board to board or just about anything else. These cables mate with the connectors listed below. They have bare wires on one end and a 6-pin JST SH connector on t...

SKU: SF-ROB-10335 | Brand: SparkFun

This pan/tilt bracket kit includes two brackets and all the hardware needed to build a pan/tilt mechanism using two servo motors. Perfect for mounting cameras, sensors, or other small payloads that need two-axis posit...

SKU: SF-COM-12766 | Brand: SparkFun

The L7812 is a three-terminal positive voltage regulator with a fixed 12V output. It provides stable local regulation with built-in protection against overcurrent, thermal overload, and short circuits, making it a rel...

SKU: SF-PRT-10287 | Brand: SparkFun

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare wires to a barrel jack...

SKU: SF-PRT-10255 | Brand: SparkFun

The LiPower board is based on the incredibly versatile TPS61200 boost converter. The board is configured to be used with a LiPo battery, has solder jumper selectable 5V and 3.3V output, and an under voltage protection...