SparkFun

SKU: SF-CAB-10215 | Brand: SparkFun

A standard USB 2.0 Type-A to Micro-B cable, 1.8 m (6 ft) in length. Micro USB is the standard connector found on a wide range of development boards, microcontrollers, and electronics accessories. Key Features USB 2...

SKU: SF-DEV-12660 | Brand: SparkFun

The SparkFun MP3 Player Shield is an awesome MP3 decoder with the capabilities of storing music files onto a run-of-the-mill microSD card, thus giving you the ability toadd music or sound effects to any project. Wi...

SKU: SF-PRT-10158 | Brand: SparkFun

These are a longer version of our standard break away headers. They are 20mm long which allows you use them socket to socket. The plastic separator can be slid up or down to accommodate your needs. You will ge...

SKU: SF-PRT-09916 | Brand: SparkFun

This is a simple four wire cable. Great for jumping from board to board or just about anything else. There is a 4-pin JST connector on one end, bare cable on the opposite end. It also comes with the mating connector f...

SKU: SF-COM-09850 | Brand: SparkFun

A pack of 25 super bright white through-hole LEDs, ideal for indicators, lighting effects, and general-purpose use in electronics projects. Supplied in a reusable ESD-safe bag. Key Features Super Bright White – Hig...

SKU: SF-DEV-09716 | Brand: SparkFun

This is the newest revision of our FTDI Basic. We now use a SMD 6-pin header on the bottom, which makes it smaller and more compact. Functionality has remained the same. This is a basic breakout board for the FTDI...

SKU: SF-COM-09650 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very standard green LED. The lens is 3mm in diameter, and is diffused.

SKU: SF-COM-09479 | Brand: SparkFun

The LN298 is a high voltage, high current, dual full-bridge motor driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Comes in a stagge...

SKU: SF-PRT-09385 | Brand: SparkFun

A pack of 10 premium 12″ (30 cm) male-to-female jumper wires for breadboarding, prototyping, and connecting to 0.1″ pitch headers. Each wire has a male pin on one end and a female socket on the other, making them vers...

SKU: SF-COM-13326 | Brand: SparkFun

Sometimes when you have too many choices, it’s hard to make a good decision. In fact, there are times when you just want a bag of LEDs, just one of each, that’s all you want. Well here you go! The LED Mixed Bag con...

SKU: SF-PRT-10588 | Brand: SparkFun

Simple breakout board for the 3.5mm audio jack. Use this breakout (shipped bare) to allow breadboard or SIP access to the super-common 3.5mm audio jack. All five pins are broken out.

SKU: SF-COM-08890 | Brand: SparkFun

This is your standard fridge magnet, perfect for holding up quite a bit of weight. Grade C8, ceramic disk magnet. Magnetization is throughout the thickness of the magnet. We used this part with the SparkFun flame kits...

SKU: SF-SEN-23352 | Brand: SparkFun

QR codes are a great way for users to communicate with microcontrollers, whether it’s passing WiFi credentials to set up connectivity or sending personal information to fill out a digital badge. Reading them from a ma...

SKU: SF-DEV-21247 | Brand: SparkFun

The SparkFun USB-C Host Shield provides all the digital logic and analogue circuitry needed to add USB peripheral/host control to your Arduino. Interface with and control any USB 2.0 compatible device — thumb drives, ...

SKU: SF-SEN-19512 | Brand: SparkFun

The Arducam Camera Module V3 delivers 16MP autofocus imaging for Raspberry Pi projects, powered by the Sony IMX519 sensor. With twice the resolution of the V2 camera module, it's an affordable yet high-performance opt...

SKU: SF-SEN-19096 | Brand: SparkFun

The SparkFun BME688 Environmental Sensor is a breakout that combines a gas scanning sensor with temperature, humidity, and barometric pressure sensing for a complete environmental sensor in a single package. The ga...

SKU: SF-PRT-18769 | Brand: SparkFun

This 3xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover as well as an ON/OFF switch that can be used to control power to your project. The ...

SKU: SF-WRL-18086 | Brand: SparkFun

This small form-factor antenna offers a 2.4GHz frequency range. These antennas offer adhesive backing that simplifies mounting within the device for a FPC or PCB. Just connect the antenna using the attached U.FL conne...

SKU: SF-DEV-18077 | Brand: SparkFun

🛇 Product Restrictions: To access certain features of the ATECC608A, users will need to contact Microchip and sign an NDA contract to obtain the complete datasheet. Due to the required NDA - technical support, an Ar...

SKU: SF-WRL-18569 | Brand: SparkFun

This RP-SMA to U.FL Cable is commonly used to attach WiFi, Bluetooth, or nRFxxx based devices to a 2.4GHz antenna. What makes this unassuming cable special is the slightly longer length of 150mm (compared to 100mm). W...