SparkFun

SKU: SF-DEV-18426 | Brand: SparkFun

The MyoWare® 2.0 Arduino Shield is designed to easily connect up to six MyoWare 2.0 Muscle Sensors and Link Shields using 3.5mm TRS-to-TRS audio cables. The board comes pre-populated with male headers so all you would...

SKU: SF-COM-16273 | Brand: SparkFun

A 16 mm deluxe thumb joystick similar to the analogue sticks found in PlayStation controllers. Two 10K potentiometers provide analogue position data for the full range of motion on both axes, and a built-in select but...

SKU: SF-COM-14622 | Brand: SparkFun

An adjustable potentiometer can open up many interesting user interfaces. With this rotary potentiometer just turn the dial and the resistance changes. This potentiometer has a ¼" metal knurled shaft diameter, solder ...

SKU: SF-SEN-09198 | Brand: SparkFun

The Minisense 100 from Measurement Specialties is a low-cost cantilever-type vibration sensor loaded by a mass to offer high sensitivity at low frequencies. Useful for detecting vibration and ‘tap’ inputs from a user....

SKU: SF-SEN-09197 | Brand: SparkFun

A flexible piezo vibration sensor from Measurement Specialties, commonly used for detecting flex, touch, vibration, and shock. The PVDF polymer film generates a small AC voltage (up to ±90 V) when it moves, which can ...

SKU: SF-BOB-09110 | Brand: SparkFun

This is the breakout board for the thumb joystick. Pins are broken out to a 0.1" header and includes 4 mounting holes in the corners.

SKU: SF-DEV-08777 | Brand: SparkFun

Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to dig...

SKU: SF-SEN-08681 | Brand: SparkFun

These are very thin variable potentiometers. By pressing down on various parts of the strip, the resistance linearly changes from 100Ohms to 10,000Ohms allowing the user to very accurately calculate the relative po...

SKU: SF-SEN-00242 | Brand: SparkFun

The Sharp GP2Y0A21YK is an infrared proximity sensor with an analogue voltage output that varies with distance — from 3.1 V at 10 cm to 0.4 V at 80 cm. It uses an IR emitter and position-sensitive detector to measure ...

SKU: SF-SEN-11574 | Brand: SparkFun

Heart rate data can be really useful whether you’re designing an exercise routine, studying your activity or anxiety levels or just want your shirt to blink with your heart beat. The problem is that heart rate can be ...

SKU: SF-COM-10468 | Brand: SparkFun

The MSGEQ7 is a CMOS graphic equaliser IC that divides the audio spectrum into seven frequency bands: 63 Hz, 160 Hz, 400 Hz, 1 kHz, 2.5 kHz, 6.25 kHz, and 16 kHz. Each band is peak-detected and multiplexed to provide ...

SKU: SF-SEN-12642 | Brand: SparkFun

The SparkFun Sound Detector is a small and very easy to use audio sensing board with three different outputs. The Sound Detector not only provides an audio output, but also a binary indication of the presence of so...

SKU: SF-SEN-09674 | Brand: SparkFun

This very long force sensitive resistor - over 2 feet - has a sensing area of 0.25x24". This FSR from Interlink Electronics will vary its resistance depending on how much pressure is being applied to the sensing area....

SKU: SF-COM-09542 | Brand: SparkFun

The QRE1113 is a small IR reflectance sensor. This sensor is often used in line following robots because, if it can sense if a surface is white or black. There are four pins on the QRE1113 - two control the IR em...

SKU: SF-COM-09426 | Brand: SparkFun

A compact resistive analog joystick similar to those found on the PSP1000. Unlike traditional thumbstick joysticks, this one has a distinctive flat "slide" feel with a removable rubber thumb pad. Connect to an Arduin...

SKU: SF-KIT-20673 | Brand: SparkFun

The Base version of the SparkFun OpenLog Data Collector Kit with Machinechat is an easy way to organize and display your data with the OpenLog Artemis and JEDI One. The SparkFun OpenLog Artemis (without IMU) is an ope...

SKU: SF-KIT-20683 | Brand: SparkFun

The Environmental Monitoring version of the SparkFun OpenLog Data Collector Kit with Machinechat is an easy way to organize and display your data from an included BME280 Qwiic Atmospheric Sensor with the OpenLog Artem...

SKU: SF-DEV-18425 | Brand: SparkFun

The MyoWare 2.0 Link Shield connects a MyoWare 2.0 Muscle Sensor to your Arduino microcontroller via a 3.5mm TRS cable. Simply snap the Link Shield onto your Muscle Sensor using the built-in snap connectors, connect a...

SKU: SF-WRL-16781 | Brand: SparkFun

The SparkFun MicroMod ESP32 Processor Board brings Espressif's ESP32 into the MicroMod ecosystem via the M.2 connector interface. It provides WiFi and Bluetooth connectivity with the processing power of a dual-core Te...

SKU: SF-SEN-17052 | Brand: SparkFun

The MQ-136 is a Hydrogen Sulfide detection sensor with a sensing range of 1 - 200ppm. The sensing element is SnO2, which has lower conductivity in clean air. When H₂S gas exists, the sensor’s conductivity gets higher ...