SparkFun

SKU: SF-SEN-13285 | Brand: SparkFun

This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that period, the ‘alarm’ pin will go low.This unit works great from 5...

SKU: SF-BOB-13282 | Brand: SparkFun

This is a breakout board for the WS2812B RGB LED. The WS2812B is actually an RGB LED with a WS2811 built right into the LED! All the necessary pins are broken out to 0.1" spaced headers for easy bread-boarding. Severa...

SKU: SF-WRL-13287 | Brand: SparkFun

The SparkFun ESP8266 WiFi Shield is an Arduino compatible shield for the ESP8266 WiFi SoC – a leading platform for Internet of Things (IoT) or WiFi-related projects. There are a variety of designs based around the ...

SKU: SF-PRT-11214 | Brand: SparkFun

MOSFETs are awesome. They’re like a switch that you flip electronically! This SparkFun MOSFET Power Controller makes it easy to switch a battery supply on and off using your favorite microcontroller. The board also ha...

SKU: SF-SEN-13266 | Brand: SparkFun

The SparkFun MAX31855K Thermocouple Breakout is a simple 14-bit resolution, SPI-compatible, serial interface thermocouple digitizer that makes reading a wide range of temperatures possible. A thermocouple works by ...

SKU: SF-BOB-13263 | Brand: SparkFun

Introducing the 3.3V SparkFun FT231X Breakout board, complete with the full UART hardware handshake feature! The pin-out of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino board...

SKU: SF-SEN-11084 | Brand: SparkFun

Life has its ups and downs, so why not measure them? The MPL3115A2 is a MEMS pressure sensor that provides Altitude data to within 30cm (with oversampling enabled). The sensor outputs are digitized by a high reso...

SKU: SF-SEN-11005 | Brand: SparkFun

This non-invasive current sensor (also known as a split-core current transformer) clamps around the supply line of an electrical load to measure how much current is flowing through it. The sensor acts as an inductor, ...

SKU: SF-TOL-13114 | Brand: SparkFun

A dual-sided resistor lead forming tool for bending component leads to precise through-hole spacing. One side handles 1/4W resistors with spacing from 0.4" to 1.5" (10–38mm), and the other handles 1/2W resistors with ...

SKU: SF-COM-10855 | Brand: SparkFun

If you ever find yourself connecting handfuls of resistors to the ground bus of your breadboard, you may consider these SIL-packaged resistors as a time-saving alternative. This Singe In-Line component is actually 5 i...

SKU: SF-SEN-13030 | Brand: SparkFun

The SparkFun RFID Reader Breakout converts the 2mm pin spacing of ID-series RFID readers to breadboard-friendly 0.1" headers. Compatible with the ID-3LA, ID-12LA, and ID-20LA readers, this board lets you solder the re...

SKU: SF-PRT-13010 | Brand: SparkFun

This is a simple 2x3 female PTH header. This header is in the common configuration for an ISP connector. Each pin has a spacing of 0.1" in between each other. Documents: Datasheet

SKU: SF-TOL-10719 | Brand: SparkFun

This is a replacement soldering tip for our Hakko FX-888 soldering iron. This is a bevel type of soldering tip. Replacing the tip is very easy - simply unscrew the shield, slip the replacement tip in, and screw the...

SKU: SF-COM-10613 | Brand: SparkFun

A digital potentiometer that lets you control a voltage divider with serial signals from your microcontroller. Wire it up like a standard potentiometer, then use digital commands to adjust the wiper position — no mech...

SKU: SF-TOL-10602 | Brand: SparkFun

Precision curved tweezers with an ESD-safe coating, ideal for handling surface-mount components and other small electronic parts. The fine curved tip provides excellent control when placing or removing tiny components...

SKU: SF-PRT-10592 | Brand: SparkFun

This is the SMD version of PRT-07948, which is the unit we like to use as RTC backup and SRAM backup for GPS units. Holds battery in place with friction. The metal housing connects to the positive side of the batte...

SKU: SF-WRL-10533 | Brand: SparkFun

A simple 315 MHz wireless receiver module that pairs with 315 MHz transmitters to create a basic one-way data link. It fits easily into a breadboard and works well with microcontrollers like Arduino for straightforwar...

SKU: SF-PRT-10512 | Brand: SparkFun

A snap-in 9V battery holder with a 5.5mm/2.1mm centre-positive barrel jack connector. The battery clicks securely into place, and three mounting holes allow you to attach the holder to an enclosure or chassis. Key Fe...

SKU: SF-COM-10468 | Brand: SparkFun

The MSGEQ7 is a CMOS graphic equaliser IC that divides the audio spectrum into seven frequency bands: 63 Hz, 160 Hz, 400 Hz, 1 kHz, 2.5 kHz, 6.25 kHz, and 16 kHz. Each band is peak-detected and multiplexed to provide ...

SKU: SF-DEV-12857 | Brand: SparkFun

The Beaglebone Black is a low-cost credit-card-sized development platform with good support from a fast growing community. The Beaglebone Black differs slightly from the regular version by providing you with an onboar...