SparkFun

SKU: SF-PRT-10255 | Brand: SparkFun

The LiPower board is based on the incredibly versatile TPS61200 boost converter. The board is configured to be used with a LiPo battery, has solder jumper selectable 5V and 3.3V output, and an under voltage protection...

SKU: SF-PRT-12711 | Brand: SparkFun

The SparkFun USB LiPoly Charger is a single-cell Li-Ion/Li-Polymer battery charging board based on the MCP73831T. It charges 3.7V LiPo cells at a selectable rate of 500 mA or 100 mA via a solder jumper, with power inp...

SKU: SF-PRT-10217 | Brand: SparkFun

If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The SparkFun LiPo Charger Basic is stripped down of all features and just does one thing well - charge 3.7V LiPo cells ...

SKU: SF-BOB-10160 | Brand: SparkFun

Here is a real time clock based on the DS3234 Real Time Clock IC. The DS3234 is a low-cost, extremely accurate SPI bus real-time clock with an integrated temperature-compensated crystal oscillator and crystal. Th...

SKU: SF-BOB-10124 | Brand: SparkFun

This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can re...

SKU: SF-PRT-12590 | Brand: SparkFun

This is a SMD 6 pin right angle female header. We realized that we have had the male version of this header available for awhile now, but never the female. Now you have the ability to get both! Pins have 0.1" spacin...

SKU: SF-COM-09998 | Brand: SparkFun

Knobs are a great way to finish off your project and make it easier to adjust the level of your death ray. This knob mates to a 0.25" shaft with a set screw.

SKU: SF-ROB-12567 | Brand: SparkFun

This buzzer is an add-on for your RedBot that gives your robot the ability to make awesome beep-boop noises or alerts when something interesting (or terrible) happens. The buzzer works by making use of two I/O pi...

SKU: SF-PRT-09915 | Brand: SparkFun

This is a simple three wire cable. Great for jumping from board to board or just about anything else. There is a 3-pin JST connector on one end, bare cable on the opposite end. It also comes with the mating connector ...

SKU: SF-COM-09856 | Brand: SparkFun

A pack of 25 standard red 5 mm through-hole LEDs. Supplied in a reusable ESD-safe bag. Specifications Colour – Red Size – 5 mm through-hole Forward Voltage – ~1.8–2.2 V Forward Current – 20 mA Package Contents...

SKU: SF-COM-09773 | Brand: SparkFun

This is a 5mm PTH fuse clip intended to be used with our Glass Fuses. Note: These are sold in single units. If you intend to secure a fuse using these clips you’ll need two clips. We recommend ordering two. Part #: ...

SKU: SF-PRT-09739 | Brand: SparkFun

A red insulated binding post for connecting single-wire leads. The coloured cap screws up and down to clamp securely onto the connecting wire, and the post accepts standard banana plugs for quick, reliable connections...

SKU: SF-ROB-09454 | Brand: SparkFun

The SparkFun QRE1113 Line Sensor Breakout (Digital) is a compact IR reflectance sensor board that outputs a digital signal based on surface reflectivity. It uses a capacitor discharge circuit — the faster the 10 nF ca...

SKU: SF-SEN-09417 | Brand: SparkFun

This is a simple, thumbnail-size RFID tag. These tags are great for sensing presence, identification, etc., and they’re small, so they can be easily sewn into clothing or inserted into enclosures. Each tag comes with ...

SKU: SF-SEN-09405 | Brand: SparkFun

A simple-to-use MQ-6 gas sensor for detecting liquefied petroleum gas (LPG) — primarily propane and butane — in the air. The sensor detects concentrations from 200 to 10,000 ppm with high sensitivity and fast response...

SKU: SF-SEN-09404 | Brand: SparkFun

This is a simple-to-use compressed natural gas (CNG) sensor, suitable for sensing natural gas (composed of mostly Methane [CH4]) concentrations in the air. The MQ-4 can detect natural gas concentrations anywhere from ...

SKU: SF-LCD-29467 | Brand: SparkFun

  The SparkFun Red Vision Touch Display for Pico features a 2.0", 320x240px capacative touch LCD mounted on a breakout board designed to plug directly into the Control Board on the Experiential Robotics ...

SKU: SF-WRL-16781 | Brand: SparkFun

The SparkFun MicroMod ESP32 Processor Board brings Espressif's ESP32 into the MicroMod ecosystem via the M.2 connector interface. It provides WiFi and Bluetooth connectivity with the processing power of a dual-core Te...

SKU: SF-GPS-15733 | Brand: SparkFun

The SparkFun NEO-M9N GPS Breakout with on-board chip antenna is a high quality, GPS board with equally impressive configuration options. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it ca...

SKU: SF-WRL-15484 | Brand: SparkFun

The SparkFun Artemis Module is a compact 10 × 15 mm wireless module built around the Ambiq Apollo3 Cortex-M4F processor with BLE 5.0. Running at 48 MHz (with 96 MHz turbo mode), it draws as little as 6 µA per MHz — ma...