SparkFun

SKU: SF-PRT-10588 | Brand: SparkFun

Simple breakout board for the 3.5mm audio jack. Use this breakout (shipped bare) to allow breadboard or SIP access to the super-common 3.5mm audio jack. All five pins are broken out.

SKU: SF-COM-08890 | Brand: SparkFun

This is your standard fridge magnet, perfect for holding up quite a bit of weight. Grade C8, ceramic disk magnet. Magnetization is throughout the thickness of the magnet. We used this part with the SparkFun flame kits...

SKU: SF-DEV-21247 | Brand: SparkFun

The SparkFun USB-C Host Shield provides all the digital logic and analogue circuitry needed to add USB peripheral/host control to your Arduino. Interface with and control any USB 2.0 compatible device — thumb drives, ...

SKU: SF-SEN-19512 | Brand: SparkFun

The Arducam Camera Module V3 delivers 16MP autofocus imaging for Raspberry Pi projects, powered by the Sony IMX519 sensor. With twice the resolution of the V2 camera module, it's an affordable yet high-performance opt...

SKU: SF-PRT-18769 | Brand: SparkFun

This 3xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover as well as an ON/OFF switch that can be used to control power to your project. The ...

SKU: SF-DEV-18077 | Brand: SparkFun

🛇 Product Restrictions: To access certain features of the ATECC608A, users will need to contact Microchip and sign an NDA contract to obtain the complete datasheet. Due to the required NDA - technical support, an Ar...

SKU: SF-WRL-18569 | Brand: SparkFun

This RP-SMA to U.FL Cable is commonly used to attach WiFi, Bluetooth, or nRFxxx based devices to a 2.4GHz antenna. What makes this unassuming cable special is the slightly longer length of 150mm (compared to 100mm). W...

SKU: SF-PRT-18582 | Brand: SparkFun

This IR proximity contactless button makes for a good replacement for typical push buttons in situations where touching the button isn't required or desirable (especially in this day and age). This button includes a b...

SKU: SF-PRT-17252 | Brand: SparkFun

The micro:bit Edge Connector allows you to expand the capabilities of the micro:bit development platform. This version of the connector features 80, right angle, PTH pins. Add this part to your board to create a handy...

SKU: SF-DEV-17047 | Brand: SparkFun

The SparkFun Qwiic GPIO adds eight additional digital I/O pins to your project via I2C, based on the TCA9534 I/O Expander from Texas Instruments. Read and write pins just like standard Arduino digital pins using the i...

SKU: SF-SEN-16295 | Brand: SparkFun

The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junc...

SKU: SF-BOB-15931 | Brand: SparkFun

Buttons are an easy and tactile way to interface with your project, but why would you want to deal with debouncing, polling, and wiring up pull-up resistors? The SparkFun Qwiic Button Breakout simplifies all of those ...

SKU: SF-CAB-15463 | Brand: SparkFun

This panel mount USB-B (female) to micro-B (male) cable enables you to more easily enclose a project that contains a USB micro-B port. The cable is 6" in length and includes two 14mm M3 screws compatible with the cabl...

SKU: SF-DEV-15444 | Brand: SparkFun

The SparkFun RedBoard Artemis brings the powerful Artemis module into a familiar Arduino Uno footprint. Built around the Ambiq Apollo3 processor, it runs at 48 MHz (with 96 MHz turbo mode), includes BLE 5.0, and draws...

SKU: SF-SEN-15569 | Brand: SparkFun

This is the HC-SR04 ultrasonic distance sensor. This economical sensor provides 2cm to 400cm of non-contact measurement functionality with a ranging accuracy that can reach up to 3mm. Each HC-SR04 module includes an u...

SKU: SF-CAB-14743 | Brand: SparkFun

USB C is fantastic. But until we have converted all our hubs, chargers, and ports over to USB C this is the cable you’re going to need. Supporting USB 3.1 speeds, this 1 meter cable is perfect for high data rate tr...

SKU: SF-COM-15099 | Brand: SparkFun

Add another eight pins to your microcontroller using a MCP23008 port expander. The MCP23008 uses two I2C pins which can be shared with other I2C devices, and in exchange gives you eight general purpose pins. You can s...

SKU: SF-CAB-14574 | Brand: SparkFun

These 2-pin JST-SM pigtail connectors mate perfectly with LED strips and other applications that require only two lines and an option for quick connection and disconnection. Even if you don’t have a specific use for t...

SKU: SF-PRT-14417 | Brand: SparkFun

Here is a tiny 4-pin Qwiic 1mm JST connector. This connector is used on all of our Qwiic-based boards and can be used to create your own I2C-based device compatible with the Qwiic system!Additionally, this connector w...

SKU: SF-PRT-14299 | Brand: SparkFun

This is a unique two-cell AA battery holder built specifically for the BBC micro:bit. The 6" (~150mm) cable has been terminated with a JST-PH connector. The connector mates the JST socket on the micro:bit perfectly...