Prototyping

SKU: SF-TOL-12878 | Brand: SparkFun

This is 50g of high quality, Lead-Free Solder Paste, the perfect amount to keep around for prototyping and hobby projects that require a bit of SMD soldering. Solder Paste Stenciling is the easiest and quickest way t...

SKU: AF-3342 | Brand: Adafruit

This 2×40 right-angle edge connector fits directly onto the bottom edge contacts of the BBC micro:bit, providing access to all GPIO pins, power, and ground connections. The right-angle design is ideal for mounting on ...

SKU: AF-590 | Brand: Adafruit

A value pack of three Adafruit Perma-Proto Full-Sized Breadboard PCBs. Each board mirrors the layout of a standard full-size solderless breadboard with 60 rows of 5-hole connected pads, four power bus rails, and clear...

SKU: AF-1873 | Brand: Adafruit

A 16 MHz ceramic resonator with built-in load capacitors, providing a simple clock source for microcontrollers. The 3-pin package has 0.1" (2.54 mm) pin spacing for direct breadboard use — connect the two outer pins t...

SKU: AF-3347 | Brand: Adafruit

A pack of 10 tactile push buttons with a polished metal ball actuator, giving them a distinctive industrial look. The rounded top also makes them forgiving when pressed at an angle — useful for mechanical actuator set...

SKU: SF-PRT-12791 | Brand: SparkFun

This is a 2x23 pin male PTH header. This piece is in the common configuration for Beaglebone Black headers that can be broken apart to form smaller header formations. Each pin has a spacing of 0.1" in between each oth...

SKU: AF-3307 | Brand: Adafruit

Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic green protective casing, and a green LED at the tip of the switch, this Green LED Toggle Switch is sure&nb...

SKU: SF-PRT-10370 | Brand: SparkFun

This is a simple five wire cable. Great for jumping from board to board or just about anything else. There is a 5-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway header...

SKU: SF-PRT-10364 | Brand: SparkFun

This is a simple four wire cable. Great for jumping from board to board or just about anything else. There is a 4-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway header...

SKU: SF-PRT-10369 | Brand: SparkFun

A 6" (15 cm) four-wire jumper cable with 4-pin JST RE connectors on both ends, designed for board-to-board connections on standard 0.1" (2.54 mm) pitch headers. Specifications Wires – 4 Connector – 4-pin JST RE on...

SKU: SF-PRT-10368 | Brand: SparkFun

A simple 3-pin jumper wire with JST RE connectors on both ends, designed for standard 0.1" (2.54 mm) breakaway headers. Ideal for board-to-board connections, sensor hookups, and general prototyping. Specifications ...

SKU: SF-PRT-10367 | Brand: SparkFun

This is a simple two wire cable. Great for jumping from board to board or just about anything else. There is a 2-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers...

SKU: DF-FIT0455-G | Brand: DFRobot

INTRODUCTION Comes in your choice of red, green, blue, yellow or white. This button locks and lights up when pushed. It's perfect for DIY projects which require a button and it's easy to mou...

SKU: AF-1814 | Brand: Adafruit

A 10-segment LED bar graph display in pure green — a vivid, true green that's much closer to blue than typical "yellow green" LEDs. At just 1" (25mm) long, it's compact enough to plug directly into a breadboard while ...

SKU: SF-PRT-10365 | Brand: SparkFun

This is a simple five wire cable. Great for jumping from board to board or just about anything else. There is a 5-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway hea...

SKU: SF-PRT-10366 | Brand: SparkFun

A simple 6-pin jumper wire cable with JST RE connectors on both ends. Perfect for board-to-board connections using standard 0.1" (2.54mm) breakaway headers. At 4" (100mm) long, it keeps wiring tidy in compact builds. ...

SKU: SF-PRT-10362 | Brand: SparkFun

This is a simple two wire cable. Great for jumping from board to board or just about anything else. There is a 2-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway head...

SKU: SF-PRT-12769 | Brand: SparkFun

Add SD card storage to your next project with this simple, through-hole SD/MMC socket. SD and MMC cards communicate over an SPI serial bus (as well as a 4-bit proprietary bus), making them easy to interface with micro...

SKU: AF-1817 | Brand: Adafruit

This 1.2″ 8×8 LED Matrix features 64 blue LEDs arranged in a square grid, perfect for building scrolling signs, simple animations, or small pixel displays. The compact package plugs directly into a breadboard with 0.1...

SKU: AF-1818 | Brand: Adafruit

This 1.2″ 8×8 LED Matrix features 64 amber LEDs arranged in a square grid, perfect for building scrolling signs, simple animations, or small pixel displays. The compact package plugs directly into a breadboard with 0....