Prototyping

SKU: AF-4954 | Brand: Adafruit

For crafting your very own custom keyboard, these Kailh Brown Linear mechanical key switches are deeee-luxe! With smooth actuation and Cherry MX compatibility, they're lovely when you want a tactile keyst...

SKU: AF-4899 | Brand: Adafruit

The Adafruit SPI Flash SD Card breakout features an XTSD 512 MB chip — an SD card in an SMT package that you can wire up like standard SPI flash but use with existing SD card libraries. It comes pre-formatted as a 512...

SKU: DF-FIT0723 | Brand: DFRobot

Protect your electronics projects from rain and water splash with this IP68-rated waterproof enclosure. Made from sturdy ABS with a transparent polycarbonate lid and silicone gasket, it's built for both indoor and out...

SKU: AF-4183 | Brand: Adafruit

A 20-pack of 6×6 mm tactile push buttons with soft translucent silicone tops. Instead of a hard plastic actuator, these buttons feature a molded silicone cap that provides a soft, grippy feel under the finger while re...

SKU: AF-3633 | Brand: Adafruit

Our Raw Male/Female Jumper Wires are perfect for making a custom jumper wire sets for wire harnesses or jumpering between headers on PCBs. These premium jumpers are a little over 6", almost 8" (about 200mm)...

SKU: SF-PRT-14494 | Brand: SparkFun

These are your run-of-the-mill ¼ Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and other prototyping applications, these 1M ohm resistors make excellent pull-ups, pull-downs and current limiters. ...

SKU: AF-1057 | Brand: Adafruit

You have some frickin' sharks at your lair, and you're thinking "it would be really great if I could attach some lasers to them" and then you see these little laser diode modules: what great timing! These encapsulated...

SKU: AF-4100 | Brand: Adafruit

Connect this to that without soldering using these small alligator clip test leads. 18" long cables with color-coded alligator clips on both ends. You get 6 pieces in 6 unique colors. Strong and grippy, these al...

SKU: AF-1504 | Brand: Adafruit

A clean, rounded 16mm panel-mount momentary pushbutton in green. This normally-open micro-switch connects the contacts only while pressed, making it a straightforward input for any project enclosure or control panel. ...

SKU: AF-1502 | Brand: Adafruit

A clean, rounded 16mm panel-mount momentary pushbutton in yellow. This normally-open micro-switch connects the contacts only while pressed, making it a straightforward input for any project enclosure or control panel....

SKU: AF-2138 | Brand: Adafruit

A compact 2-pin screw terminal block with 2.54mm (0.1") pitch, designed to fit directly into perfboard and protoboards. Terminal blocks provide reliable, tool-adjustable PCB-to-wire connections that are easy to mainta...

SKU: AF-2006 | Brand: Adafruit

Silicone-sheathing wire is super-flexible and soft, and its also strong! Able to handle up to 200°C and up to 600V, it will do when PVC covered wire wimps out. We like this wire for being extremely supple and flexible...

SKU: AF-1881 | Brand: Adafruit

A 2-metre length of black 26AWG stranded-core wire with a flexible silicone sheath. Silicone-covered wire is significantly more supple and heat-resistant than standard PVC wire — rated to handle up to 200 °C and 600 V...

SKU: AF-2165 | Brand: Adafruit

A popular low-dropout (LDO) 3.3 V linear voltage regulator based on the LD1117 in a TO-220 package. With approximately 1 V dropout and up to 800 mA output current, it cleanly steps down 5–15 V supplies to a regulated ...

SKU: AF-1993 | Brand: Adafruit

This 2×20 (40-pin) IDC box header is the matching connector for 40-pin GPIO ribbon cables used with Raspberry Pi models that have a 40-pin GPIO header. Solder it onto perfboard to create a breakout point for your Pi's...

SKU: AF-2463 | Brand: Adafruit

Add a micro-slice standard solderless breadboard to your Perma-Proto or other perf-board. This 4x4 point solder-less breadboard is a good way to add some solderless prototyping space if you just need to have...

SKU: AF-2671 | Brand: Adafruit

These 2 mm pitch 40-pin break-apart male headers are designed for modules and boards that use 2 mm pin spacing instead of the standard 2.54 mm (0.1″) pitch. Each pack includes five 40-pin strips that can be easily sna...

SKU: DF-FIT0188 | Brand: DFRobot

A compact 10-segment LED bar graph in super bright red. Each segment is an individual LED housed together in a standard-size package, making it easy to drive from a microcontroller or shift register. Low power consump...

SKU: SF-PRT-09279 | Brand: SparkFun

This is a 8-pin female header, with extra long legs – great for stacking Arduino shields. Pins are spaced by 0.1". Documents: Datasheet

SKU: SF-PRT-09044 | Brand: SparkFun

A standard 2-pin jumper shunt used to create an electrical connection between two adjacent pin headers. Commonly used to configure settings on development boards, select operating modes, or bridge header pins on PCBs....