Prototyping

SKU: DF-FIT0323 | Brand: DFRobot

This 100-piece assortment gives you a handy spread of common through-hole diodes for prototyping, repairs and general project builds. It covers small-signal diodes, standard rectifiers, fast-recovery diodes and Schott...

SKU: SF-COM-00533 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very standard red LED. The lens is 3mm in diameter, and is diffused.

SKU: SF-PRT-00132 | Brand: SparkFun

Through-hole RJ11 socket with PCB mounting posts. 6-pin connection - housing accepts common telephone connectors/wiring. If you need a board for this connector be sure to check out our SparkFun RJ11 Breakout. Two b...

SKU: AF-161 | Brand: Adafruit

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ. To use, connect one side o...

SKU: AF-239 | Brand: Adafruit

This is a 'full-size' breadboard, 830 tie points. Good for small and medium projects. It's 2.2" x 7" (5.5 cm x 17 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the powe...

SKU: DF-FIT0365 | Brand: DFRobot

 INTRODUCTION Premium quality jumper wires for prototyping. Made with 26AWG multi-strand wire and sturdy male pins. Each jumper wire is approximately 210mm in length. Each pack comes with 30 jumper wires in a...

SKU: SF-COM-11372 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a blue lens. It has a typical forward voltage of 3.4V and ...

SKU: SF-COM-11121 | Brand: SparkFun

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow.Features: 3.0-3.4VDC Forward Voltage 20mA Forward Current 40 degree viewing angle 150-180 MCD output ...

SKU: SF-PRT-10897 | Brand: SparkFun

These are 155mm long jumpers terminated as male to male. Use these to jumper from any female header on any board, to any other female header. Multiple jumpers can be installed next to one another on a 0.1" header. Com...

SKU: SF-COM-12903 | Brand: SparkFun

Sometimes when you have too many choices, it’s hard to make a good decision. In fact, there are times when you just want a bag of LEDs, just one of each, that’s all you want. Well too bad, you are getting two of each!...

SKU: SF-PRT-10571 | Brand: SparkFun

These are simple 2-position screw terminals with 2.54mm pitch pins. Rated up to 150V @ 6A, this terminal can accept 30 to 18AWG wire. The 2.54mm pitch will line up with standard 0.1" perf boards.Documents: Datasheet

SKU: AF-756 | Brand: Adafruit

Transistors are powerful little electronic switches, and we really like these NPN transistors whenever we need to control medium-power electronics such as small motors, solenoids, or IR LEDs. We find them so handy, th...

SKU: AF-3393 | Brand: Adafruit

A dual-ganged 10K linear potentiometer with a built-in on/off switch — two components in one convenient panel-mount package. The dual 10 kΩ linear-taper pots share a grippy shaft that turns smoothly without shifting o...

SKU: AF-3468 | Brand: Adafruit

The Chip Quik No-Clean Liquid Flux Pen is great for all rework, solder, de-solder, and reflow applications! In particular this one is from the rework-champs at Chip Quik. Liquid flux helps solder to "c...

SKU: SF-PRT-09749 | Brand: SparkFun

A 2-pin right-angle JST PH series connector for through-hole PCB mounting. With a 2 mm pin pitch, this is the standard connector used on most single-cell LiPo batteries, making it ideal for battery-powered projects an...

SKU: LB-LR0178-350 | Brand: Little Bird

SKU: LB-LS000A | Brand: Little Bird

A pack of 30 tactile pushbutton switches in six vibrant colours — blue, white, yellow, green, black, and red. Each 12mm switch comes with a snap-on square cap, making it easy to create colour-coded controls for your p...

SKU: LB-LS6511 | Brand: Little Bird

A 30-metre kit of flexible silicone hook-up wire in red and black, ideal for power wiring in electronics projects. The 22AWG gauge suits a wide range of applications from breadboard prototyping to permanent installati...

SKU: LB-LS3506 | Brand: Little Bird

This 2×20 pin extra tall male GPIO header stands 12 mm high, providing additional clearance when soldering onto HATs, Bonnets, or custom boards for Raspberry Pi. It's ideal for boards that don't come with headers pre-...

SKU: AF-5588 | Brand: Adafruit

Here's a handy 6cm x 8cm Proto-board PCB that is meant for use with 2mm pitch parts - like maybe an XBee. Both sides have a green silkscreen with some row/column markings. Note that these don't ...