Prototyping

SKU: AF-161 | Brand: Adafruit

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ. To use, connect one side o...

SKU: AF-239 | Brand: Adafruit

This is a 'full-size' breadboard, 830 tie points. Good for small and medium projects. It's 2.2" x 7" (5.5 cm x 17 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the powe...

SKU: DF-FIT0365 | Brand: DFRobot

 INTRODUCTION Premium quality jumper wires for prototyping. Made with 26AWG multi-strand wire and sturdy male pins. Each jumper wire is approximately 210mm in length. Each pack comes with 30 jumper wires in a...

SKU: SF-COM-11372 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a blue lens. It has a typical forward voltage of 3.4V and ...

SKU: SF-COM-11121 | Brand: SparkFun

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow.Features: 3.0-3.4VDC Forward Voltage 20mA Forward Current 40 degree viewing angle 150-180 MCD output ...

SKU: SF-PRT-10897 | Brand: SparkFun

These are 155mm long jumpers terminated as male to male. Use these to jumper from any female header on any board, to any other female header. Multiple jumpers can be installed next to one another on a 0.1" header. Com...

SKU: SF-COM-12903 | Brand: SparkFun

Sometimes when you have too many choices, it’s hard to make a good decision. In fact, there are times when you just want a bag of LEDs, just one of each, that’s all you want. Well too bad, you are getting two of each!...

SKU: SF-PRT-10571 | Brand: SparkFun

These are simple 2-position screw terminals with 2.54mm pitch pins. Rated up to 150V @ 6A, this terminal can accept 30 to 18AWG wire. The 2.54mm pitch will line up with standard 0.1" perf boards.Documents: Datasheet

SKU: AF-756 | Brand: Adafruit

Transistors are powerful little electronic switches, and we really like these NPN transistors whenever we need to control medium-power electronics such as small motors, solenoids, or IR LEDs. We find them so handy, th...

SKU: AF-3468 | Brand: Adafruit

The Chip Quik No-Clean Liquid Flux Pen is great for all rework, solder, de-solder, and reflow applications! In particular this one is from the rework-champs at Chip Quik. Liquid flux helps solder to "c...

SKU: SF-PRT-09749 | Brand: SparkFun

A 2-pin right-angle JST PH series connector for through-hole PCB mounting. With a 2 mm pin pitch, this is the standard connector used on most single-cell LiPo batteries, making it ideal for battery-powered projects an...

SKU: LB-LR0178-350 | Brand: Little Bird

SKU: AF-5588 | Brand: Adafruit

Here's a handy 6cm x 8cm Proto-board PCB that is meant for use with 2mm pitch parts - like maybe an XBee. Both sides have a green silkscreen with some row/column markings. Note that these don't ...

SKU: AF-5487 | Brand: Adafruit

These ultra-fine wired LEDs are designed for model-makers and crafters but they could also come in handy for folks who want to add tiny points of light to a design without needing SMT-level soldering skills. Use ...

SKU: DF-FIT0861 | Brand: DFRobot

A set of five solderless snap-down connectors for joining 10 mm wide, 3-wire LED strips without soldering. Simply align the strip's copper pads with the connector contacts and snap the cover down for a firm electrical...

SKU: DF-FIT0867 | Brand: DFRobot

A set of five solderless right-angle connectors for joining 10 mm wide, 3-wire LED strips at 90° corners. Each connector has snap-down contacts on both ends with colour-labelled wires and marked polarity for easy, too...

SKU: AF-5180 | Brand: Adafruit

This Simple USB Type C breakout is kinda interesting, it looks similar to this USB Type C SMT Inline Breakout Board, but it's an 'inline' style with pads for soldering to the common USB 1.1/2.0 connections. We se...

SKU: DF-FIT0720 | Brand: DFRobot

These patch test hooks provide a solderless way to make signal and low-current connections between boards, sensors, and modules. The hook clips grab onto pins, pads, and component legs — perfect for prototyping with c...

SKU: AF-4748 | Brand: Adafruit

A 150-piece assortment of spade quick-connect terminals in three common sizes, complete with matching insulating sheaths. These crimp-on connectors are widely used in electronics for fast, secure connections to micro ...

SKU: AF-3893 | Brand: Adafruit

The JST PH 3-Pin to Male Header Cable converts a JST PH 3-pin connector into three individual colour-coded wires, each terminated with a 0.1" (2.54 mm) male header pin. It's ideal for extending sensor or LED connectio...