Prototyping

SKU: DF-FIT0244 | Brand: DFRobot

A pack of 50 basic 3mm LEDs in five colours — 10 each of red, green, yellow, white, and blue. Handy for prototyping, indicator lights, and Arduino projects. Specifications Forward Voltage – 1.8–2.2V Max Current – ...

SKU: SF-PRT-08272 | Brand: SparkFun

This 2 mm pitch 10-pin socket mates with XBee radio modules from Digi, allowing you to mount your XBee without soldering it directly to a PCB. You'll need two of these sockets to connect to all 20 pins on an XBee modu...

SKU: SF-COM-00533 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very standard red LED. The lens is 3mm in diameter, and is diffused.

SKU: AF-161 | Brand: Adafruit

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ. To use, connect one side o...

SKU: AF-239 | Brand: Adafruit

This is a 'full-size' breadboard, 830 tie points. Good for small and medium projects. It's 2.2" x 7" (5.5 cm x 17 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the powe...

SKU: DF-FIT0365 | Brand: DFRobot

 INTRODUCTION Premium quality jumper wires for prototyping. Made with 26AWG multi-strand wire and sturdy male pins. Each jumper wire is approximately 210mm in length. Each pack comes with 30 jumper wires in a...

SKU: SF-COM-11372 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a blue lens. It has a typical forward voltage of 3.4V and ...

SKU: SF-COM-11121 | Brand: SparkFun

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow.Features: 3.0-3.4VDC Forward Voltage 20mA Forward Current 40 degree viewing angle 150-180 MCD output ...

SKU: SF-COM-12903 | Brand: SparkFun

Sometimes when you have too many choices, it’s hard to make a good decision. In fact, there are times when you just want a bag of LEDs, just one of each, that’s all you want. Well too bad, you are getting two of each!...

SKU: SF-PRT-10571 | Brand: SparkFun

These are simple 2-position screw terminals with 2.54mm pitch pins. Rated up to 150V @ 6A, this terminal can accept 30 to 18AWG wire. The 2.54mm pitch will line up with standard 0.1" perf boards.Documents: Datasheet

SKU: AF-756 | Brand: Adafruit

Transistors are powerful little electronic switches, and we really like these NPN transistors whenever we need to control medium-power electronics such as small motors, solenoids, or IR LEDs. We find them so handy, th...

SKU: LB-LR0178-350 | Brand: Little Bird

SKU: LB-LS000A | Brand: Little Bird

A pack of 30 tactile pushbutton switches in six vibrant colours — blue, white, yellow, green, black, and red. Each 12mm switch comes with a snap-on square cap, making it easy to create colour-coded controls for your p...

SKU: LB-LS6511 | Brand: Little Bird

A 30-metre kit of flexible silicone hook-up wire in red and black, ideal for power wiring in electronics projects. The 22AWG gauge suits a wide range of applications from breadboard prototyping to permanent installati...

SKU: TB-HM3194 | Brand: Little Bird

A 12-way screw terminal strip rated at 6A and 250VAC. Can be divided into smaller sections with a sharp knife, making it easy to create custom-sized terminal blocks for any project. Each terminal block includes a moun...

SKU: LB-LS3506 | Brand: Little Bird

This 2×20 pin extra tall male GPIO header stands 12 mm high, providing additional clearance when soldering onto HATs, Bonnets, or custom boards for Raspberry Pi. It's ideal for boards that don't come with headers pre-...

SKU: AF-5487 | Brand: Adafruit

These ultra-fine wired LEDs are designed for model-makers and crafters but they could also come in handy for folks who want to add tiny points of light to a design without needing SMT-level soldering skills. Use ...

SKU: LB-LS3381-W | Brand: Little Bird

A 12 mm panel-mount momentary push button with a smooth dome-shaped cap in white, pre-wired with 20 cm red and black leads for easy connection. Normally open — pressing the button closes the contacts. Key Features ...

SKU: LB-LS1891 | Brand: Little Bird

HS1891 DAC Module CJMCU-1334 UDA1334A I2S DAC Audio Stereo Decoder Module Board 3.3V - 5V Feature: This fully-featured UDA1334A I2S Stereo DAC breakout is a perfect match for any I2S-output audio interface.&nbsp...

SKU: LB-LR0589-GREEN | Brand: Little Bird

A 12 mm panel-mount momentary push button with a smooth dome-shaped cap in green. Normally open — pressing the button closes the contacts. The dome design provides a satisfying tactile feel and sits flush with the pan...