New Arrivals

SKU: AF-3275 | Brand: Adafruit

If the holidays promise anything, it’s almost certainly a deluge of photographs. Instead of taking out your smartphones, why not build your own camera? With one of Adafruit’s best selling screens and an official...

SKU: SF-PRT-12885 | Brand: SparkFun

This is the Sunny Buddy, a maximum power point tracking (MPPT) solar charger for single-cell LiPo batteries. This MPPT solar charger provide you with the ability to get the most possible power out of your solar panel ...

SKU: DF-DWG0006-L | Brand: DFRobot

INTRODUCTION A stylish imprint T-Shirt featured with DFRobot's special maker design, 100% cotton. One of DFRobot must-haves! SPECIFICATION ...

SKU: SF-BOB-10467 | Brand: SparkFun

This simple breakout board makes it easy to use our LED tactile switches in a breadboard, or your next project. Note: Populate the board according to the polarity of the LED on the switch. The markings for the swi...

SKU: SF-PRT-10461 | Brand: SparkFun

These nylon standoffs are 3/8" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. Each standoff has an outer diameter of 6mm. Sold in pack...

SKU: AF-50 | Brand: Adafruit

We sure love the ATmega328 here at Adafruit, and we use them a lot for our own projects. The processor has plenty of GPIO, Analog inputs, hardware UART SPI and I2C, timers and PWM galore - just enough for most...

SKU: SF-COM-10443 | Brand: SparkFun

This is a simple LED-illuminated tactile button with a clear cap. It’s just like a basic tactile button, but it lights up blue! So now you can get visual feedback, or light up your project. These have a 12mm body a...

SKU: SF-PRT-10452 | Brand: SparkFun

Standard Philips-head 4-40 screws. They are ½" long and come in packs of ten. This is the screw size we use in most of the holes for our breakout boards. Check below for other associated hardware.

SKU: SF-COM-10442 | Brand: SparkFun

A tactile push button with a built-in red LED, combining momentary switching with visual feedback in a single component. Press the button and it lights up red — ideal for control panels, interactive projects, and anyw...

SKU: SF-COM-10440 | Brand: SparkFun

This is a simple LED-illuminated tactile button with a green cap. It’s just like a basic tactile button, but it lights up green! So now you can get visual feedback, or light up your project. These have a 12mm body and...

SKU: SF-COM-10439 | Brand: SparkFun

This is a simple LED-illuminated tactile button with a clear cap. It’s just like a basic tactile button, but it lights up white! So now you can get visual feedback, or light up your project. These have a 12mm body and...

SKU: SF-SEN-12787 | Brand: SparkFun

This is the SparkFun RGB and Gesture Sensor, a small breakout board with a built in APDS-9960 sensor that offers ambient light and color measuring, proximity detection, and touchless gesture sensing. With this RGB and...

SKU: AF-3307 | Brand: Adafruit

Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic green protective casing, and a green LED at the tip of the switch, this Green LED Toggle Switch is sure&nb...

SKU: DF-FIT0455-Y | Brand: DFRobot

INTRODUCTION Comes in your choice of red, green, blue, yellow or white. This button locks and lights up when pushed. It's perfect for DIY projects which require a button and it's easy to mou...

SKU: SF-WIG-12772 | Brand: SparkFun

The SparkFun Logomatic v2 is a versatile serial and analogue data logger built around the NXP LPC2148 ARM7 microcontroller. It logs data to a microSD card in FAT32 format and appears as a USB mass storage device, so l...

SKU: DF-FIT0455-R | Brand: DFRobot

INTRODUCTION Comes in your choice of red, green, blue, yellow or white. This button locks and lights up when pushed. It's perfect for DIY projects which require a button and it's easy to mou...

SKU: DF-FIT0455-W | Brand: DFRobot

A self-locking illuminated push button with a white LED indicator. When pressed, the button locks into position and the LED lights up; press again to release. The built-in LED includes a resistor for direct 5–12V oper...

SKU: AF-618 | Brand: Adafruit

A compact 1.8" TFT display with true 18-bit colour (262,144 shades) and 160 × 128 resolution. It uses a simple SPI interface requiring only 4–5 digital pins and features two white LED backlights running on 3.3 V. Driv...

SKU: DF-FIT0455-B | Brand: DFRobot

INTRODUCTION Comes in your choice of red, green, blue, yellow or white. This button locks and lights up when pushed. It's perfect for DIY projects which require a button and it's easy to mou...

SKU: SF-TOL-10326 | Brand: SparkFun

The Heaterizer XL-3000 is a compact 300W heat gun suitable for heat-shrink tubing, basic plastic forming, and low-temperature PCB rework. It heats up quickly and is sized conveniently for bench work and electronics us...